RF Attenuators

From Land Boards Wiki
Revision as of 11:45, 7 September 2021 by Blwikiadmin (talk | contribs)
Jump to navigation Jump to search

Homebrew Attenuators

Atten 30dB 20dV P1812-720px.jpg

Attenuators

Chart mW vs dbM.PNG

30 dB Attenuator

Atten30dB P116-720px.jpg

30dB Attenuator.PNG

  • Built
    • Standard 5% resistor values
    • R1 = 820 in parallel with 22K = 790.6 ohms
    • R2 = 2 paralleled 120 Ohm 1/4W resistors paralleled with 470 ohms = 53.2 ohms
    • Flat from 0-30 MHz
    • Measured attenuation is flat
      • -30.01dB at 1 MHz
      • -30.24dB at 30 MHz
    • Input Impedance - 53.1 ohms, 21.3nF
    • SWR 1.06
    • 1/2W max (5VDC max, 0 ohm source)
  • NanoVNA scan data

30dB Attenuator NanoVNA Setup Curve 900MHz.PNG

30dB Attenuator NanoVNA Data 900MHz.PNG

  • LTSPICE Simulation

LTSPice 30dB.PNG

20 dB Attenuator

Atten 20dB P115-720px.jpg

20dB Attenuator.PNG

  • Build
    • Standard 5% resistor values
    • R1 = 2 of 510 in parallel also in parallel with 8.2K = 247.3 ohms
    • R2 = 2 paralleled 150 Ohm 1/2W resistors paralleled with 330 ohms = 61.11 ohms
    • Flat from 0-30 MHz
    • Measured attenuation is flat
    • Input Impedance - tbd ohms, tbd nF
    • SWR tbd
    • 1W max (8.6 V max, 0 ohm source)

20dB Attenuator NanoVNA Setup Curve 900MHz.PNG

20dB Attenuator NanoVNA Data 900MHz.PNG

  • LTSPICE Simulation

LTSPice 20dB.PNG

10 dB Attenuator

File:Atten 10dB P115-720px.jpg

10dB Attenuator.PNG

  • Build
    • Standard 5% resistor values
    • R1 = 2 of 150 in parallel also in parallel with 1.5K = 71.43 ohms (0.3% error)
    • R2 = 3 of 330 Ohm 1/4W parallel resistors paralleled with 810 ohms = 96.85 ohms (0.62% error)
    • Flat from 0-30 MHz
    • Measured attenuation is flat
    • Input Impedance - tbd ohms, tbd nF
    • SWR tbd
    • 3/4W max (9.1 V max, 0 ohm source)

File:10dB Attenuator NanoVNA Setup Curve 900MHz.PNG

File:10dB Attenuator NanoVNA Data 900MHz.PNG

  • LTSPICE Simulation

LTSPice 10dB.PNG

Attenuator Construction

  • Single side copper clad PCB
    • Approx 2"x1"
  • Clean with steel wool
  • Solder SMA connectors
    • Use large alligator clips to hold while soldering
    • Solder on sides only

Atten 01 SMAs 720px.jpg

  • Cut "T" Shaped pads
    • I used nibbler
  • Center fits between connector ground pins
  • Glue down pads with Superglue

Atten 02 Pads 720px.jpg

  • Solder center pin with big solder blob
    • A bit too high for direct contact
  • Verify raised pad does not short to ground

Atten 03 Solder CenterPads 720px.jpg

  • Solder side resistor(s)
  • Leave room for center resistor(s)

Atten 04 Solder Side Resistors 720px.jpg

  • Measure side resistors from pad to ground
  • Should match value
  • Solder center resistor(s)

Atten 05 Solder Center Resistors 720px.jpg

  • Verify no shorts between centers and ground