Difference between revisions of "STM32 Blue Pill"

From Land Boards Wiki
Jump to navigation Jump to search
(Created page with "=== Blue Pill Board Features === * Used on BLUE-PILL-HUB card * STM32F103 ** 72 MHz CPU sclocl ** 64KB Flash (most have 128KB) ** 20 KB SRAM ** 3.3V regulator ** 16 MHz c...")
 
Line 24: Line 24:
  
 
[[File:STM32F103C8T6-Blue-Pill-Pin-Layout.gif]]
 
[[File:STM32F103C8T6-Blue-Pill-Pin-Layout.gif]]
 +
 +
== Arduino IDE ==
 +
 +
* [https://github.com/rogerclarkmelbourne/Arduino_STM32 Hardware files to support STM32 boards, on Arduino IDE 1.8.x including LeafLabs Maple and other generic STM32F103 boards]
 +
** [https://github.com/rogerclarkmelbourne/Arduino_STM32/wiki Arduino STM32 Wiki]
 +
** [https://github.com/rogerclarkmelbourne/Arduino_STM32/wiki/Installation Installation]
 +
* [https://www.instructables.com/id/Programming-STM32-Blue-Pill-Via-USB/ Arduino Alternative - STM32 Blue Pill Programming Via USB]
 +
 +
=== Uploading Code to Blue Pill ===
 +
 +
* FTDI connection to Blue Pill Hub FTDI connector
 +
** FTDI TX (to Blue Pill RX) (PA10 pin on STM32)
 +
** FTDI RX (to Blue Pill Tx) (PA9 pin on STM32)
 +
* Set Switch (or jumper) on Blue Pill module set towards center of card to upload card to board
 +
 +
[[File:BluePill_Jumper.png]]
 +
 +
* In Arduino IDE,
 +
** Tools
 +
*** Board "Generic..."
 +
*** Upload method: "Serial..."
 +
*** Port: [the comm port]
 +
 +
[[File:ArduinoIDE_Tools_Menu.png]]
 +
 +
* Upload code
 +
** Takes a while
 +
* Set Switch (or jumper) on Blue Pill module set towards edge of card to run
 +
* Press reset button

Revision as of 11:58, 6 February 2021

Blue Pill Board Features

  • Used on BLUE-PILL-HUB card
  • STM32F103
    • 72 MHz CPU sclocl
    • 64KB Flash (most have 128KB)
    • 20 KB SRAM
    • 3.3V regulator
    • 16 MHz crystal
    • 1 of x12-bit, A/D converter
    • 7-channel DMA controller
    • SPI, I2C, UART interfaces
    • 7 timers
  • MicroUSB
  • Reset button
  • Download jumper
    • Replaced with a slide switch
  • Power LED
  • PC 13 LED
  • SWD connector
  • RTC crystal
  • Warning: The +5V pins on this board are directly connected to the +5V pin of the USB connector. There is no protection in place. Do not power this board through USB and an external power supply at the same time.


STM32F103C8T6-Blue-Pill-Pin-Layout.gif

Arduino IDE

Uploading Code to Blue Pill

  • FTDI connection to Blue Pill Hub FTDI connector
    • FTDI TX (to Blue Pill RX) (PA10 pin on STM32)
    • FTDI RX (to Blue Pill Tx) (PA9 pin on STM32)
  • Set Switch (or jumper) on Blue Pill module set towards center of card to upload card to board

BluePill Jumper.png

  • In Arduino IDE,
    • Tools
      • Board "Generic..."
      • Upload method: "Serial..."
      • Port: [the comm port]

ArduinoIDE Tools Menu.png

  • Upload code
    • Takes a while
  • Set Switch (or jumper) on Blue Pill module set towards edge of card to run
  • Press reset button