Difference between revisions of "Serial Terminal"

From Land Boards Wiki
Jump to navigation Jump to search
Line 1: Line 1:
 +
This is an inexpensive and small serial terminal design. This design can drive 80x25 text and graphics displays. This design is based on Grant Searle's Monitor and keyboard controllers. This design has been implemented on two cards, the Display Processor and Serial I/O Processor.
 +
 +
[[File:SerialTerminal-P1010506-720px.jpg]]
 +
 
== Display Processor ==
 
== Display Processor ==
 
This is an inexpensive and small serial terminal design. This design can drive 80x25 text and graphics displays. This design is based on Grant Searle's Monitor and keyboard controllers. This design has been implemented on two cards, this card and Serial I/O Processor - which is the other half of this terminal.
 
  
 
Here's Grant's schematic:
 
Here's Grant's schematic:

Revision as of 11:20, 16 April 2020

This is an inexpensive and small serial terminal design. This design can drive 80x25 text and graphics displays. This design is based on Grant Searle's Monitor and keyboard controllers. This design has been implemented on two cards, the Display Processor and Serial I/O Processor.

SerialTerminal-P1010506-720px.jpg

Display Processor

Here's Grant's schematic:

Searle-DisplayProc.gif

Video controller specification

  • Very easy to interface to, fast and requires no host/external memory
  • Character set
  • Full "CGA" (8x8) character definitions as used on the IBM PC (DOS).
  • Screen size
    • Text - 80x25, 40x25, 80x12, 40x12, Graphics 160x100 or ANY mix (defined per 1 of 25 rows)
  • Resolution
    • 640x200 for 80 char text
    • 160x100 for graphics
  • Fonts
    • Font sizes are defined for each line
    • All chars on the same line have the same font size and style
  • Graphics
    • Any part of the active screen, up to 160x100 pixels
    • Each pixel individually addressable
    • Defined on any of the 25 screen lines
  • Video output
    • Standard composite monochrome video
    • PAL or NTSC timing
    • Non-interlaced so no flicker
  • Display memory
    • 2000 chars internal + 25 line attributes - no host memory needed
    • Very fast update and scrolling whichever interface is used
  • Interface
    • 8 bit data bus (requires 10 I/O pins)
    • 4 bit data bus (requires 6 I/O pins)
  • two-wire (I2C) uses only 2 pins
    • I2C (thanks to Dave Curran for his guidance and code on this) supports low (100KHz) and high (400KHz) speed clocks or higher (1MHz or more easily achievable).
  • Hardware
    • Very low cost - two chips - ATmega328 and 74HCT166 (Shift Register)
  • Connectors
    • J1 - Video Connector
    • RCA Jack
      • Center is signal
      • Outside is ground

P1 - Card Interconnect

  • 2x8 header, 0.1" pitch
  • Pinout
  1. VCC
  2. VCC
  3. ID0
  4. ID1
  5. ID2 - MOSI for ISP Download cable
  6. ID3 - MISO for ISP Download cable
  7. ID4 - SCK for ISP Download cable
  8. ID5
  9. ID6
  10. ID7
  11. Unused
  12. RESET*
  13. ACK/SDA (R4 terminator for I2C interface)
  14. AVAIL/SCL (R3 terminator for I2C interface)
  15. GND
  16. GND

ISP Cable

P1 Pin	Description	ISP Pin	Description	Color
1	VCC	2	VCC	Red
2				
3				
4				
5	MOSI	4	MOSI	Green
6	MISO	1	MISO	Grey
7	SCK	3	SCK	Yellow
8				
9				
10				
11				
12	RESET	5	RST	White
13				
14				
15	GND	6	GND	Black
16				
<pre>

Configuration Resistors

  • Configuration Resistor values can also be set through soft switches in the code
    • R5 - Two-wire interface (I2C)
    • R6 - 4-bit interface
    • R7 - 10K for NTSC, open for PAL
    • R3, R4 - I2C Termination resistors - Install for I2C termination - typical = 2.2K

Software

avrdude -U lfuse:w:0xc6:m -U hfuse:w:0xd9:m -e -F -v -patmega328p -carduino -PCOM8 -b19200 -D -Uflash:w:"C:\Users\doug_000\Documents\GitHub\lb-Arduino-Code\LBCards\DisplayProc\AssemblerApplication1\AssemblerApplication1\Debug\AssemblerApplication1.hex":i -C"C:\Program Files (x86)\Arduino\hardware\tools\avr\etc\avrdude.conf"

Checkout

  • Saw a blinking cursor

SIOPROC-01-640px.jpg

Serial I/O Processor

  • This is an inexpensive and small serial terminal design. This design can drive 80x25 text and graphics displays. This design is based on Grant Searle's Monitor and keyboard controllers. This design has been implemented on two cards, this card and Display Processor - which is the other half of this terminal.
  • Here's Grant's schematic:

Searle-SIOProc.gif

Features

  • Serial interface
  • Fully buffered 115200 baud, handshake on receive, TTL levels.
  • Keyboard interface
  • PC PS/2 standard keyboard connector, accepts standard keyboards made for PCs. Keyboard LED illumination implemented, and allows for caps lock and num lock.

Hardware

  • Two cards
  • 8-bit interface connector for card-to-card connections

Connectors

P1 - Card Interconnect

  • 2x8 header, 0.1" pitch
  • Connector matches the pinout of the other card so it can be mated directly to the other card via 1:1 cable or a female header on this card
  • Pinout
  1. VCC
  2. VCC
  3. ID0
  4. ID1 - CS* for ISP Download cable
  5. ID2 - MOSI for ISP Download cable
  6. ID3 - MISO for ISP Download cable
  7. ID4 - SCK for ISP Download cable
  8. ID5
  9. ID6
  10. ID7
  11. Unused
  12. RESET*
  13. ACK/SDA (R4 terminator for I2C interface)
  14. AVAIL/SCL (R3 terminator for I2C interface)
  15. GND
  16. GND

P2 - PS/2 Keyboard

PS2Conn.png

  • 1x4 header, 0.1" pitch
  1. GND
  2. VCC
  3. KBCLK
  4. KBDAT
  • PS/2 Adapter Cable

S-l1600-Adapter-Cable-720px.jpg

  • Ordered this cable from ebay.
  • Replaced 5 pin connector with 4 pin 0.1" pitch "Dupont" connector
  • Pinout of cable after re-wiring with new connector
PS/2 Pin	P2 Pin	Description	Color
1	4	Data	TBD
2	N/C	N/C	N/A
3	1	GND	TBD
4	2	+5V	TBD
5	3	Clk	TBD
6	N/C	N/C	N/A

P3 - 5V FTDI/Power Connector

File:S-l1600.jpg

  • 1x6 header, 0.1" pitch
  • Pinout
  1. GND
  2. RTS
  3. VCC (+5V)
  4. TX
  5. RX
  6. N/C

P4 - In-System Programmer (ISP) Connector

  • Cable for use with ArduinoISP programmer
  • 0.1" pitch "Dupont" connector
  • 2x3
  1. MISO
  2. VCC
  3. SCK
  4. MOSI
  5. RESET*
  6. GND

Configuration Resistors

  • Configuration Resistor values can also be set through soft switches in the code
    • R1, R2 - I2C termination - install to terminate - typically 2.2K
    • R5 - Two Wire Interface output (I2C)
    • R6 - 4-bit Interface

Software

avrdude -U lfuse:w:0xc6:m -U hfuse:w:0xd9:m -e -F -v -patmega328p -carduino -PCOM8 -b19200 -D -Uflash:w:"C:\Users\doug_000\Documents\GitHub\lb-Arduino-Code\LBCards\SIOProc\GccApplication1\GccApplication1\Debug\GccApplication1.hex":i -C"C:\Program Files (x86)\Arduino\hardware\tools\avr\etc\avrdude.conf"

Rev X1 Issues

  • FTDI handshake moved from P3-6 to pin P3-2
  • Cut etch at FTDI connector P3-6
  • Add wire U1-26 to P3-2

Assembly Sheet