Difference between revisions of "Slew Rate Controller on ER-PROTO-01"
Jump to navigation
Jump to search
Blwikiadmin (talk | contribs) |
Blwikiadmin (talk | contribs) |
||
(7 intermediate revisions by the same user not shown) | |||
Line 23: | Line 23: | ||
== Wiring == | == Wiring == | ||
− | === | + | === Pots on Controls Card === |
+ | |||
+ | * Install 100 Ohms resistor at R1, R2 | ||
+ | * Install B100K at RV1, RV2 | ||
+ | * Add wire RV1-1 to RV1-2 | ||
+ | * Add wire RV2-1 to RV2-2 | ||
− | + | [[file:ER-PROTO-01_SLEW_POTS.PNG]] | |
− | [[file: | + | [[file:RV_Conns.PNG]] |
=== Jacks on Controls Card === | === Jacks on Controls Card === | ||
Line 38: | Line 43: | ||
[[file:ER-PROTO-01_SLEW_JACKS.PNG]] | [[file:ER-PROTO-01_SLEW_JACKS.PNG]] | ||
− | === | + | === J6 - Eurorack Power Jack === |
− | * Install | + | * Install 14 pin socket for U1 |
− | * | + | ** Orient socket so Pins 1-7 face +12V bus (right side) |
− | * Add wire | + | * Add wire U1-4 to +12V |
− | * Add wire | + | * Add wire U1-11 to -12V |
+ | * Install 10 pin IDC connector at J6 | ||
+ | ** Pin 1 to "STRIPE" | ||
− | [[file:ER-PROTO- | + | [[file:ER-PROTO-01_SLEW_EURORACK_PWR_J6_.PNG]] |
− | |||
− | |||
=== Input Buffers === | === Input Buffers === | ||
− | + | * Node: J1-T, J38-8 to first open row left side center of 3 pins | |
− | + | * R3: 100K ohm from first open row left side right of 3 pins to GND (don't solder yet) | |
− | + | * R6: 1K ohm from first open row left side left pin to next open row | |
− | + | * Wire R6 new side to U1- | |
− | + | * Node: J2-T, J38-4 to first open row right side center of 3 pins | |
− | * Node: J1-T, | + | * 100K ohm from first open row right side left of 3 pins to GND |
− | * | ||
− | * Node: J2-T, | ||
− | * | ||
[[file:ER-PROTO-01_SLEW_BUFF_AMPS.PNG]] | [[file:ER-PROTO-01_SLEW_BUFF_AMPS.PNG]] |
Latest revision as of 21:57, 12 November 2022
Contents
Features
- Simple dual slew rate limiter
- Used for portamento effects or to smooth out a stepped voltage from a sequencer, or for general audio or CV smoothing
- Each channel contains a buffer with 100K input impedance suitable for pitch CVs
- The slew pot affects the charging of a large capacitor connected to a second amplifier
- The second amp provides buffering for output to isolate the output jack from the actual slewing function
- Control range of 0-10s (approx.)
- Power: +12V @ 5mA, -12V @ 5mA
Credits
Jacks/Controls
- 2 Slew Rate adjustment Pots
- 4 Jacks
- 2 Input jacks
- 2 Output jacks
Wiring
Pots on Controls Card
- Install 100 Ohms resistor at R1, R2
- Install B100K at RV1, RV2
- Add wire RV1-1 to RV1-2
- Add wire RV2-1 to RV2-2
Jacks on Controls Card
- Install J1-J4
- Add wire J1-S to J3-S
- Add wire J3-S to J4-S
- Add wire J2-S to J4-S
J6 - Eurorack Power Jack
- Install 14 pin socket for U1
- Orient socket so Pins 1-7 face +12V bus (right side)
- Add wire U1-4 to +12V
- Add wire U1-11 to -12V
- Install 10 pin IDC connector at J6
- Pin 1 to "STRIPE"
Input Buffers
- Node: J1-T, J38-8 to first open row left side center of 3 pins
- R3: 100K ohm from first open row left side right of 3 pins to GND (don't solder yet)
- R6: 1K ohm from first open row left side left pin to next open row
- Wire R6 new side to U1-
- Node: J2-T, J38-4 to first open row right side center of 3 pins
- 100K ohm from first open row right side left of 3 pins to GND
Output Buffers
Video