Difference between revisions of "VGAX49"

From Land Boards Wiki
Jump to navigation Jump to search
Line 75: Line 75:
 
** 0.7V into 75 Ohms = 9.33 mA
 
** 0.7V into 75 Ohms = 9.33 mA
 
* R-2R values
 
* R-2R values
** 5% resistor values are 510 ohms, 1K ohms and 2K ohms
+
** 5% resistor values are 470 ohms, 1K ohms and 2.2K ohms
*** Produce 0.679V
+
*** Produces 0.697V
  
 
[[file:VideoDAC_3bit_Voltage.PNG]]
 
[[file:VideoDAC_3bit_Voltage.PNG]]

Revision as of 13:22, 14 July 2022

Tindie-mediums.png

VGAX49 P901-cropped-720px.jpg

Features

  • Digital VGA adapter
  • 16-bit digital video
    • 5:6:5 (R:G:B) mapping (maximum)
    • 2:2:2 (R:G:B) mapping (option)
  • Uses summing resistors
  • DB-15F connector
  • 49x49mm ODAS form factor
  • Mounting holes

Connectors

VGAX49.PNG

J1 - Digital Connections

P1 - VGA connector

VGAX49 J1.PNG

  • Ex: R0 is the least significant bit (connects to 10K resistor)

Simulation

  • Each color is independently driven and can be considered individually
  • Critical design criteria is output voltage and current capability of the driving part
  • Use common value, 5% resistors
  • Each resistor is about 2X the value of the previous resistor
  • 1V is drive level for VGA specification
    • VGA presents a 75 Ohm load
    • 1V at 75 Ohms is 13.3 mA
  • Series resistors present a voltage divider between the resistors on the card and the VGA load
  • The resistor with the smallest resistance value has larger current from the source device pin
  • Current switches from source to sink depending on the voltages on the other resistors
  • Each resistor is 2X the value of the previous resistor
  • Too much effort is put into using precision resistors - the human eye is not that picky

VGA - Ideal Drive 2 bit Case

  • 3.3V driver requires less than 8 mA
    • Configure FPGAs output as 3.3V LVTTL and 8mA drive current
  • Ideal case drive current
  • Full scale video = 0.7V
  • VGA Termination resistor = 75 Ohms
    • 0.7V into 75 Ohms = 9.33 mA
  • R-2R values
  • Voltage steps are:

VGA Sim 2R Voltage.PNG

  • Current steps are:

VGA Sim 2R Current.PNG


VGA - Ideal Drive 3 bit Case

  • 3.3V driver requires less than 8 mA
    • Configure FPGAs output as 3.3V LVTTL and 8mA drive current
  • Ideal case drive current
  • Full scale video = 0.7V
  • VGA Termination resistor = 75 Ohms
    • 0.7V into 75 Ohms = 9.33 mA
  • R-2R values
    • 5% resistor values are 470 ohms, 1K ohms and 2.2K ohms
      • Produces 0.697V

VideoDAC 3bit Voltage.PNG

5:6:5 Resistor Simulation

  • Assumptions
    • 3.3V Drive out of FPGA
    • 8 mA max drive current (typical FPGA drive current)
  • Using common value, 5% resistors
  • Model most significant bit resistor as 1/2 the full scale voltage (0.7V) single resistor value
  • 75 Ohm terminator in monitor
  • 0.7V at 75 Ohms = 9.33mA
  • Series resistor - single resistor value is (3.3V-0.7V)/9.33mA is 278.6 Ohms
  • First resistor is 2x 278.57 = 557.1 Ohms
  • Each resistor is 2x the previous resistor
  • Simulation uses the same 4 value steps (real case would have 2^5 or 2^6 steps)
  • Voltage steps

VideoDAC 6bit Voltage.PNG

  • Current steps

VideoDAC 6bit Current.PNG

Schematic

Assembly Sheet