Difference between revisions of "PDP-11 ON RETRO-EP4CE15"

From Land Boards Wiki
Jump to navigation Jump to search
 
(195 intermediate revisions by the same user not shown)
Line 1: Line 1:
'''Work in Progress'''
+
[[File:PDP-11_FrontPanel_P512-cropped-720px.jpg]]
 +
 
 +
== Overview ==
 +
 
 +
[https://pdp2011.sytse.net/wordpress/pdp-11/ Sytse van Slooten's website describes his PDP2011 as]
 +
 
 +
<pre>
 +
a re-creation of the well-known series of PDP-11 computer systems in VHDL. Everything that is needed to run a PDP-11 system is included; you can run a complete Unibus PDP-11 system with console, disks and other peripherals on a simple low-cost FPGA development board. The original V5-V7 versions of Unix, BSD 2.11, and the original DEC operating systems for the PDP-11 work.
 +
</pre>
 +
 
 +
=== Highlights ===
 +
 
 +
* You can configure PDP2011 to be 11/20, 11/24, 11/34, 11/44, 11/45, 11/70 or 11/94
 +
** This also sets up 18- or 22-bit memory management, special instructions, EIS and FPU
 +
* The model specific instructions and the most important differences between the system models are implemented to the point that many of the original MAINDEC test programs run without error
 +
* PDP2011 can drive a [[LEDS-SWITCHES-2|PDP-11]] console
 +
* There are disk controllers for RK, RL and RM/RP disks; these use SD cards to store the disk image on
 +
* The system can be hooked up to a network; it includes a DEUNA compatible Ethernet frontend that works with the ENC424J600 Ethernet chip
 +
** You can run DECNET on RSTS and RSX, or TCP/IP on 2.11BSD
 +
* The PDP2011 project includes a terminal core to interface to a VGA screen and PS2 keyboard; you can combine it on the same FPGA you run the PDP-11 system, or run it on separate board
 +
** You can configure the terminal to be a vt100 or a vt105
 +
* Up to four serial ports can be configured for the console, additional terminals, links to other systems etc
 +
 
 +
== PDP2011 FPGA Builds ==
 +
 
 +
The following model codes will produce working systems:
 +
<PRE>
 +
20; 11/20 system, no MMU, no FPU
 +
34; 11/34 system, 18-bit MMU (2-bit ACF),FPU
 +
44; 11/44 system, 22-bit MMU (2-bit ACF),FPU,Unibus map
 +
45; 11/45 system, 18-bit MMU (3-bit ACF),FPU
 +
70; 11/70 system, 22-bit MMU (3-bit ACF),FPU,Unibus map
 +
94; 11/94 system, 22-bit MMU (2-bit ACF),FPU,Unibus map
 +
</PRE>
 +
 
 +
* My PDP-11 Builds
 +
** PDP-11/45
 +
** PDP-11/70
 +
 
 +
=== PDP-11/45 ===
 +
 
 +
** [https://github.com/douggilliland/Retro-Computers/wiki/PDP-11-45-Stand-alone PDP-11/45 Standalone] (no Front Panel)
 +
** [https://github.com/douggilliland/Retro-Computers/wiki/PDP-11-45-with-Front_Panel PDP-11/45] with [[LEDS-SWITCHES-2|Front Panel]] in Stackup
 +
** [https://github.com/douggilliland/Retro-Computers/wiki/PDP-11-45-in-Box PDP-11/45] in [[Multicomp_in_a_Box|Multicomp in a Box]]
 +
** [https://github.com/douggilliland/Retro-Computers/tree/master/PDP-11/PDP2011/PDP_11_45_InBox_FrPanel PDP-11/45] in [[Multicomp_in_a_Box|Multicomp in a Box]] with External Front Panel
 +
 
 +
=== PDP-11/70 ===
 +
 
 +
** [https://github.com/douggilliland/Retro-Computers/wiki/PDP-11-70-Stand-alone PDP-11/70 Standalone] (no Front Panel)
 +
** [https://github.com/douggilliland/Retro-Computers/wiki/PDP-11-70-with-Front_Panel PDP-11/70] with [[LEDS-SWITCHES-2|Front Panel]] in Stackup
 +
** [https://github.com/douggilliland/Retro-Computers/wiki/PDP-11-70-in-Box PDP-11/70] in [[Multicomp_in_a_Box|Multicomp in a Box]]
 +
** [https://github.com/douggilliland/Retro-Computers/tree/master/PDP-11/PDP2011/PDP_11_70_InBox_FrPanel PDP-11/70] in [[Multicomp_in_a_Box|Multicomp in a Box]] with External Front Panel
 +
 
 +
== Hardware ==
 +
 
 +
* [[QM Tech Cyclone V FPGA Board]]
 +
 
 +
[[file:QMTECH_5CEFA2F23_Datasheet_CCA_Pic.PNG]]
 +
 
 +
* [[RETRO-EP4CE15]] FPGA base board
 +
 
 +
[[file:P1473-720px.jpg]]
 +
 
 +
* FPGA card mounted on base board
  
 
[[File:RETROEP4CE15_REV4_P376-annotated-720px.jpg]]
 
[[File:RETROEP4CE15_REV4_P376-annotated-720px.jpg]]
  
== Build ==
+
* [[LEDS-SWITCHES-2]] board
 +
 
 +
[[file:PDP-11_FrontPanel_P512-cropped-720px.jpg]]
 +
 
 +
== Disks (SD card images) that work with PDP2011 build ==
 +
 
 +
=== PDP-11/45 Disks ===
 +
 
 +
==== DOS/BATCH-11 (rk05) ====
 +
 
 +
* Switch settings
 +
** RK = Slide Switch 2 (in box)
 +
** Other Slide Switches off
 +
* [https://infogalactic.com/info/DEC_BATCH-11/DOS-11 DEC BATCH-11/DOS-11]
 +
* [https://archive.org/details/bitsavers_decpdp11do11RAssemblerProgrammersManualMay71_2572677 dos-batch - EC-11-ASDB-D PAL-11R Assembler Programmers Manual May71]
 +
* [https://github.com/douggilliland/Retro-Computers/tree/master/PDP-11/Disks/rk05/dos_rk DOS/BATCH-11 (rk05) Disk Image]
 +
** Write to SD card - used Balena Etcher (windows) to write SD card
 +
 
 +
==== RT-11 4.0 (rk05) ====
 +
 
 +
* Switch settings
 +
** RK = Slide Switch 2 (in box)
 +
** Other Slide Switches off
 +
* [https://en.wikipedia.org/wiki/RT-11 Wikipedia article]
 +
* [https://gordonbell.azurewebsites.net/Digital/RT-11%20System%20Users%20Guide%201977.pdf RT-11 System User's Guide] 1977
 +
* [http://bitsavers.trailing-edge.com/pdf/dec/pdp11/rt11/v5.6_Aug91/AA-5284H-TC_RT-11_System_Message_Manual_Aug91.pdf RT–11 System Message Manual]
 +
* [https://web.archive.org/web/20070928022401/http://www.oshistory.net/metadot/index.pl?id=2526;isa=Category;op=show Release History]
 +
* [https://cryptosmith.com/2013/10/19/digitals-rt-11-file-system/ Digital’s RT-11 File System]
 +
* [https://github.com/douggilliland/Retro-Computers/tree/master/PDP-11/Disks/rk05/rt11_v4_rk RT-11 4.0 (rk05) Disk Image]
 +
** Write to SD card - used Balena Etcher (windows) to write SD card
 +
 
 +
==== RT-11FB 4.0 (rk05) ====
 +
 
 +
* Switch settings
 +
** RK = Slide Switch 2 (in box)
 +
** Other Slide Switches off
 +
* RT-11FB (Foreground/Background) supported two tasks: a high-priority, non-interactive "Foreground" job, and a low-priority, interactive "Background" job
 +
* RT-11FB 4.0 (rk05)
 +
 
 +
==== RT-11 5.4 (rk05) ====
 +
 
 +
* Switch settings
 +
** RK = Slide Switch 2 (in box)
 +
** Other Slide Switches off
 +
* [https://github.com/douggilliland/Retro-Computers/tree/master/PDP-11/Disks/rk05/rt11_54_rk RT-11 5.4 (rk05) Disk Image]
 +
** Write to SD card - used Balena Etcher (windows) to write SD card
 +
* DIR or DIR/BRIEF
 +
* [https://decuser.blogspot.com/2016/01/a-tutorial-introduction-to-programming.html A tutorial introduction to programming PDP-11 Macro-11 Assembly in RT-11 v5.3]
 +
* [http://bitsavers.org/www.computer.museum.uq.edu.au/RT-11/AA-5281C-TC%20Introduction%20to%20RT-11.pdf AA-5281C-TC Introduction to RT-11 v5.1 1983]
 +
* [http://bitsavers.org/www.computer.museum.uq.edu.au/RT-11/AA-5279C-TC%20RT-11%20System%20User's%20Guide.pdf AA-5279C-TC-RT-11-5.1 System Users Guide 1983]
 +
* [http://bitsavers.org/pdf/dec/pdp11/rt11/v5.1_Jul84/AA-M239B-TC_RT-11_System_Utilities_Manual_Jul84.pdf AA-M239B-TC-RT-11-5.1 System Utilities Manual 1984]
 +
* [http://bitsavers.org/pdf/dec/pdp11/rsx11/RSX11M_V4.1_Apr83/4_ProgramDevelopment/AA-V027A-TC_macro11_Mar83.pdf AA-V027A-TC-PDP11 MACRO-11 Language Reference Manual 1983]
 +
* Power-on message similar to:
 +
<pre>
 +
              RT-11 V5.4F
 +
 
 +
Installation of RT-11 Version 5.4F is complete and you are now running
 +
RT-11 from your system volume,
 +
 
 +
Your system volume is your working volume if you have used the
 +
automatic installation (AI) procedure. If you have installed RT-11 using
 +
that procedure. DIGITAL recommends you verify the correct operation of
 +
your system's software using the VERIFY verification procedure. 
 +
To do this, enter the command:
 +
 
 +
                            IND VERIFY
  
=== FPGA Hardware ===
+
Note that VERIFY should be performed  only after the distribution
 +
media have been backed up.  This was accomplished as part
 +
of automatic installation on  all  RL02,  RX02,  TK50, and  RX50
 +
based systems,  including the  MicroPDP-11 and the Professional
 +
300.  If you have not completed automatic installation, you must
 +
perform a manual backup before using VERIFY.  Note also,  VERIFY
 +
is NOT supported on RX01 diskettes,    DECtape I or II,  or the
 +
Professional 325.
  
* Runs on [[RETRO-EP4CE15]] FPGA card
+
DIGITAL also  recommends  you  read  the  file V5NOTE.TXT, which
** Requires [[QM Tech Cyclone V FPGA Board]]
+
contains information  formalized too late to be included  in the
** Or, EP4CE55 Cyclone IV Card
+
Release Notes.  V5NOTE.TXT can be TYPED or PRINTED.
 +
</pre>
  
=== PDP2011 FPGA Builds ===
+
* Prompt is dot (.)
 +
* datime format
 +
** 01-May-99
 +
* type command
 +
** The type command will show the contents of a file, just like MS-DOS
 +
* RUN command
 +
** Dungeon for example is executed with RUN. I think you have to run .sav files.
 +
** .RUN DUNGEO
 +
* .SAV files can be run
 +
** .RUN DUNGEO
 +
* @ command
 +
** COM files are like batch scripts, and are executed with the @ infront of them.
 +
** .@STARTS.COM
 +
* SHOW command
 +
** This is a very useful command to show some info about the OS.
 +
** .SHOW
  
* [https://github.com/douggilliland/Retro-Computers/tree/master/PDP-11/PDP2011/PDP2011_20210216/RETRO-EP4CE15_CYCLONEV Our PDP-11 FPGA Builds]
+
==== UNIX V7 (rl02) ====
** [https://github.com/douggilliland/Retro-Computers/tree/master/PDP-11/PDP2011/PDP2011_20210216/RETRO-EP4CE15_CYCLONEV/PDP11_45 PDP-11/45 build]
+
 
** [https://github.com/douggilliland/Retro-Computers/tree/master/PDP-11/PDP2011/PDP2011_20210216/RETRO-EP4CE15_CYCLONEV/PDP11_70 PDP-11/70 build]
+
* Switch settings
* [https://pdp2011.sytse.net/wordpress/ PDP2011] by Sytse van Slooten - the original project
+
** RL = Slide Switch 1 (in box)
* [https://github.com/DavidJRichards/pdp2011/ David Richards PDP-11 Build on A-ESTF V2 EP4CE22 Board]
+
** Other Slide Switches off
** [https://github.com/DavidJRichards/pdp2011/wiki Wiki]
+
* [https://github.com/douggilliland/Retro-Computers/tree/master/PDP-11/Disks/rl02/Unix_v7_rl UNIX V7 (rl02) Disk Image]
** [https://github.com/DavidJRichards/pdp2011/wiki/A_ESTF A-ESTF Page]
+
** Write to SD card - used Balena Etcher (windows) to write SD card
* [https://github.com/wfjm/w11 W11 PDP-11/70 Project]
+
* Prompt is '@'
 +
* Type
 +
<pre>
 +
boot
 +
</pre>
 +
* System responds with
 +
<pre>
 +
New Boot, known devices are hp ht rk rl rp tm vt
 +
</pre>
 +
* Enter
 +
<pre>
 +
rl(0,0)rl2unix
 +
</pre>
 +
* System responds with
 +
<pre>
 +
mem = 177856
 +
</pre>
 +
* Ctrl-D to open shell
 +
* login: 'root'
 +
* Password: 'root'
 +
 
 +
* There is no halt or shutdown command, the proper way to shutdown is to do a few sync
 +
** 'sync'
 +
** 'sync'
 +
** 'sync'
 +
* and just terminate the server session with a
 +
** .qq (???)
 +
 
 +
=== PDP-11/70 disks ===
 +
 
 +
==== 211BSD (rp06) ====
 +
 
 +
* Switch settings
 +
** RP = Slide Switch 3 (in box)
 +
* [https://github.com/douggilliland/Retro-Computers/tree/master/PDP-11/Disks/rp06/211bsd 211BSD (rp06) Disk Image]
 +
** Write to SD card - used Balena Etcher (windows) to write SD card
 +
* Boot screen
 +
<pre>
 +
Hello, world [t44]: cpu 11/70
 +
boot from rp:
 +
70Boot from xp(0,0,0) at 0176700
 +
: «
 +
: xp(0,0,0)unix
 +
Boot: bootdev=05000 bootcsr=0176700
 +
2.11 BSD UNIX #115: Sat Apr 22 19:07:25 PDT 2000
 +
    sms1@curly.2bsd.com:/usr/src/sys/GENERIC
 +
phys mem  = 3932160
 +
avail mem = 3708224
 +
user mem  = 307200
 +
</pre>
 +
 
 +
* Running
 +
* Enter
 +
* At the first '#' prompt the system is in single-user mode. Just enter a ^D to continue the system startup to multi-user mode
 +
* Login: root
 +
* At the end is important to shutdown properly with a halt:
 +
 
 +
<pre>
 +
    # {pstat -T}
 +
      49/186 files
 +
      65/208 inodes
 +
      16/150 processes
 +
      11/ 46 texts active,  37 used
 +
      3/135 swapmap entries,  530 kB used, 3649 kB free, 3642 kB max
 +
      33/150 coremap entries, 2599 kB free, 2520 kB max
 +
      1/ 10  ub_map entries,    8    free,    8    max
 +
    # {mount}
 +
    /dev/xp0a on /
 +
    /dev/xp0c on /tmp
 +
    /dev/xp0d on /home
 +
    /dev/xp0e on /usr
 +
    # {halt}
 +
    syncing disks... done
 +
    halting
 +
</pre>
  
=== Software ===
+
==== RSX-11M PLUS 3.0 (rp06) ====
  
* [http://www.bitsavers.org/bits/DEC/pdp11/ PDP-11 on BitSavers]
+
* Switch settings
* [https://www.instructables.com/PiDP-11-Replica-of-the-1970s-PDP-1170/ PiDP-11: Replica of the 1970s PDP-11/70]
+
** RP = Slide Switch 3 (in box)
 +
** Other Slide Switches off
 +
* [https://github.com/douggilliland/Retro-Computers/tree/master/PDP-11/Disks/rp06/rsx11mp-30 RSX-11M PLUS 3.0 (rp06) Disk Image]
 +
** Write to SD card - used Balena Etcher (windows) to write SD card
  
=== Disk Images ===
+
== Other Disk Images ==
  
 
* RL images are in chunks of 256 bytes, and require inserting 256 bytes padding after each of those chunks
 
* RL images are in chunks of 256 bytes, and require inserting 256 bytes padding after each of those chunks
Line 36: Line 264:
 
* [https://www.retro11.de/data/oc_w11/oskits/ OS Kits]
 
* [https://www.retro11.de/data/oc_w11/oskits/ OS Kits]
  
=== Documentation ===
+
== Other PDP2011 Builds ==
 +
 
 +
* [https://pdp2011.sytse.net/wordpress/ PDP2011] by Sytse van Slooten - the original project
 +
* [https://github.com/DavidJRichards/pdp2011/ David Richards PDP-11 Build on A-ESTF V2 EP4CE22 Board]
 +
** [https://github.com/DavidJRichards/pdp2011/wiki Wiki]
 +
** [https://github.com/DavidJRichards/pdp2011/wiki/A_ESTF A-ESTF Page]
 +
 
 +
=== Software ===
 +
 
 +
* [http://www.bitsavers.org/bits/DEC/pdp11/ PDP-11 on BitSavers]
 +
* [https://www.instructables.com/PiDP-11-Replica-of-the-1970s-PDP-1170/ PiDP-11: Replica of the 1970s PDP-11/70]
 +
 
 +
== Documentation ==
  
 
* [http://www.bitsavers.org/pdf/dec/pdp11/handbooks/PDP-11_Processor_Handbook_1981.pdf PDP-11 Processor Handbook 1981] - on [http://www.bitsavers.org/ BitSavers]
 
* [http://www.bitsavers.org/pdf/dec/pdp11/handbooks/PDP-11_Processor_Handbook_1981.pdf PDP-11 Processor Handbook 1981] - on [http://www.bitsavers.org/ BitSavers]
Line 42: Line 282:
 
* [http://www.bitsavers.org/pdf/dec/pdp11/1170/PDP-11_70_Handbook_1977-78.pdf PDP-11/70 Processor Handbook]
 
* [http://www.bitsavers.org/pdf/dec/pdp11/1170/PDP-11_70_Handbook_1977-78.pdf PDP-11/70 Processor Handbook]
  
== Configuration Switches/Jumpers/LEDs ==
+
== PDP-11 Front Panel ==
 +
 
 +
=== Front Panel Pins Directly Mapped to RETRO-EP4CE15 ===
 +
 
 +
[[File:PDP-11_FrontPanel_P512-cropped-720px.jpg]]
 +
 
 +
==== Front Panel J1 ====
 +
 
 +
* [[LEDS-SWITCHES-2|Front Panel]] Card cables up to 50-pin connector on [[RETRO-EP4CE15]] Card
 +
** 32-pin connector
 +
** Wiring "flipped" and directly in order
 +
** Note extra ground/power pins on the Front Panel card
 +
 
 +
==== I/O Connector (5CEFA2F23 FPGA Card pin numbers) ====
 +
 
 +
{| class="wikitable"
 +
! Function
 +
! Marking
 +
! 5CEFA2 FPGA Pin
 +
|-
 +
| resetbtn pushbutton
 +
| PB8
 +
| PIN_M22
 +
|-
 +
| PWR LED
 +
| D8
 +
| PIN_L22
 +
|-
 +
| sdHC LED
 +
| D7
 +
| PIN_M18
 +
|-
 +
| FETch LED
 +
| D6
 +
| PIN_M20
 +
|-
 +
| sdWR LED
 +
| D5
 +
| PIN_P16
 +
|-
 +
| sdRD LED
 +
| D4
 +
| PIN_T19
 +
|-
 +
| RH Drive (rp) LED
 +
| D3
 +
| PIN_R22
 +
|-
 +
| RK Drive LED
 +
| D2
 +
| PIN_U20
 +
|-
 +
| RL Drive LED
 +
| D1
 +
| PIN_U22
 +
|-
 +
| K11 (tty1) Slide switch
 +
| SS4
 +
| PIN_P22
 +
|-
 +
| RH Drive (rp) (UP) Slide switch
 +
| SS3
 +
| PIN_T22
 +
|-
 +
| RK Drive (UP) Slide switch
 +
| SS2
 +
| PIN_V20
 +
|-
 +
| RL Drive (UP) Slide switch
 +
| SS1
 +
| PIN_V21
 +
|-
 +
|}
 +
 
 +
[[File:LEDS-SWITCHES-2_P1_FPGA_Pinout.PNG]]
 +
 
 +
==== P4 - SD Card (5CEFA2F23  FPGA pin numbers) ====
 +
 
 +
* This build works with SD and SD/HC cards
 +
 
 +
[[File:RETROEP4CE15-P4_SD_Card.PNG]]
 +
 
 +
* SDCS = U7-57 = PIN_B15
 +
* MOSI = U7-58 = PIN_C15
 +
* SCK = U7-59 = PIN_C16
 +
* MISO = U7-60 = PIN_B16
 +
* SD_DETECT - PIN_B12
 +
 
 +
=== MultiComp in Box Pins Mapping ===
 +
 
 +
==== Slide Switches/Reset Pushbutton ====
 +
 
 +
* Slide switches are on the bottom of the box
 +
 
 +
[[file:MultiCompInBox_P1992_cropped_720px.jpg]]
 +
 
 +
[[file:RETROEP4-CE15_J3.PNG]]
  
=== J3 - Configuration Jumpers (5CEFA2F23 FPGA Card pin numbers) ===
+
* Slide switches are on the bottom of the box
 +
** PIN_L17 - Slide Switch 1 (top switch) - RL Drive select
 +
** PIN_K17 - Slide Switch 2 - RK Drive select
 +
** PIN_K22 - Slide Switch 3 - RH/RP Drive select
 +
** PIN_K21 - Slide Switch 4 (bottom switch)
 +
* Reset switch is on the front of the boz
 +
** PIN_N16 - Reset Switch
  
[[File:J3-footprint.PNG]]
+
==== SD Card ====
  
[[File:J3_MAP_FPGA_PINS.PNG]]
+
* [[SD_CARD_X49|External SD Card]]
 +
* Install J3 on SD Card
 +
** Runs card off 3.3V
 +
** NO5V jumper installed
  
 
{| class="wikitable"
 
{| class="wikitable"
! DRIVE
+
! J1 PIN
! VALUE
+
! SIGNAL
! SW3
+
! COLOR
! SW2
+
! SD PIN
! SW1
+
! FPGA Pin
 +
! DIR
 +
|-
 +
| 2
 +
| 3.3V
 +
| ORG
 +
| 7
 +
| VREG 3.3V
 +
| OUT (PWR)
 
|-
 
|-
| rl
+
| 45
| SELECT
+
| sdSCLK
| OUT
+
| GRY
 +
| 3
 +
| PIN_L19
 
| OUT
 
| OUT
 +
|-
 +
| 46
 +
| sdMISO
 +
| BLU
 +
| 2
 +
| PIN_L18
 
| IN
 
| IN
 
|-
 
|-
| rk
+
| 47
| SELECT
+
| sdMOSI
| OUT
+
| WHT
| IN
+
| 4
 +
| PIN_L22
 
| OUT
 
| OUT
 
|-
 
|-
| rp
+
| 48
| SELECT
+
| sdCS
| IN
+
| VIO
 +
| 5
 +
| PIN_M22
 
| OUT
 
| OUT
| OUT
 
|-
 
|
 
| J3
 
| 5, 6
 
| 3,4
 
| 1,2
 
 
|-
 
|-
|  
+
| 49
| FPGA PIN
+
| GND
| PIN_K22
+
| GRN
| PIN_K17
+
| 1
| PIN_L17
+
| GND
 +
| OUT (PWR)
 
|-
 
|-
 
|}
 
|}
  
== Switches ==
+
==== MultiComp DB-25 Pinout ====
 +
 
 +
* [[Multicomp_in_a_Box|MultiComp in a Box]] has a DB-25 Female connector
 +
* [[DB25-02]] - DB-25 adapter with Male connector
 +
* [[LEDS-SWITCHES-2|Front panel]] card has 32-pin connector
 +
* Dupont pin cable connects the two cards
 +
* DB-25F on MultiComp in a Box as viewed from front of box
 +
 
 +
[[file:DB25F_PINS.gif]]
 +
 
 +
==== Front Panel Pinout ====
  
* [[LEDS-SWITCHES]]
+
[[file:LEDS-SWITCHES-2_P1_Pinout.PNG]]
  
[[File:LEDS-SWITCHES_P1404-720px.jpg]]
+
==== MultiComp in Box Front Panel Cabling ====
  
 
{| class="wikitable"
 
{| class="wikitable"
! Function
+
! DB25F
! J10 Pin
+
! P1(DB25-02)
! FPGA Pin
+
! FPGA J1
 +
! Signal
 +
! SW-J1
 +
! FPGA
 +
!
 +
! DB25F
 +
! P1(DB25-02)
 +
! FPGA J1
 +
! Signal
 +
! SW-J1
 +
! FPGA
 +
|-
 +
| 1
 +
| 25
 +
|
 +
|
 +
|
 +
|
 +
|
 +
|
 +
| 26
 +
|
 +
| NC
 +
|
 +
|
 +
|-
 +
| 2
 +
| 23
 +
|
 +
| GND
 +
| 32
 +
|
 +
|
 +
| 14
 +
| 24
 +
|
 +
| GND
 +
|
 +
|
 +
|-
 +
| 3
 +
| 21
 +
| 44
 +
| SS1
 +
| 5
 +
| PIN_M18
 +
|
 +
| 15
 +
| 22
 +
| 43
 +
| SS2
 +
| 8
 +
| PIN_N19
 +
|-
 +
| 4
 +
| 19
 +
| 42
 +
| SS3
 +
| 11
 +
| PIN_M21
 +
|
 +
| 16
 +
| 20
 +
| 41
 +
| SS4
 +
| 14
 +
| PIN_M20
 +
|-
 +
| 5
 +
| 17
 +
| 40
 +
| N/C
 +
|
 +
| PIN_N20
 +
|
 +
| 17
 +
| 18
 +
| 39
 +
| N/C
 +
|
 +
| PIN_N21
 +
|-
 +
| 6
 +
| 15
 +
| 38
 +
| LED1
 +
| 6
 +
| PIN_P16
 +
|
 +
| 18
 +
| 16
 +
| 37
 +
| LED2
 +
| 9
 +
| PIN_P17
 +
|-
 +
| 7
 +
| 13
 +
| 36
 +
| LED3
 +
| 12
 +
| PIN_T20
 +
|
 +
| 19
 +
| 14
 +
| 35
 +
| LED4
 +
| 15
 +
| PIN_T19
 +
|-
 +
| 8
 +
| 11
 +
| 34
 +
| LED5
 +
| 18
 +
| PIN_P22
 +
|
 +
| 20
 +
| 12
 +
| 33
 +
| LED6
 +
| 21
 +
| PIN_R21
 +
|-
 +
| 9
 +
| 9
 +
| 32
 +
| LED7
 +
| 24
 +
| PIN_R22
 +
|
 +
| 21
 +
| 10
 +
| 31
 +
| LED8
 +
| 27
 +
| PIN_T22
 +
|-
 +
| 10
 +
| 7
 +
| 30
 +
| PB8
 +
| 28
 +
| PIN_U21
 +
|
 +
| 22
 +
| 8
 +
| 29
 +
|
 +
|
 +
| PIN_U20
 +
|-
 +
| 11
 +
| 5
 +
|
 +
|
 +
|
 +
|
 +
|
 +
| 23
 +
| 6
 +
|
 +
|
 +
|
 +
|
 
|-
 
|-
| resetbtn
+
| 12
| SW9
+
| 3
| PIN_J16
+
|
 +
|
 +
|
 +
|
 +
|
 +
| 24
 +
| 4
 +
|
 +
|
 +
|
 +
|
 +
|-
 +
| 13
 +
| 1
 +
|
 +
| +3.3V
 +
| 2
 +
|
 +
|
 +
| 25
 +
| 2
 +
|
 +
| +3.3V
 +
|  
 +
|  
 
|-
 
|-
 
|}
 
|}
  
== Connectors ==
+
== Connectors on RETROEP4-CE15 Card==
  
=== P1 - VGA (5CEFA2F23 Card) ===
+
=== P1 - VGA ===
  
 
* videoR0 = U8-49 = PIN_E12
 
* videoR0 = U8-49 = PIN_E12
Line 129: Line 685:
  
 
* fpgaRx1 (in) = PIN_C11
 
* fpgaRx1 (in) = PIN_C11
** Needs weak pullup
 
*** set_instance_assignment -name WEAK_PULL_UP_RESISTOR ON -to rxd1
 
 
* fpgaTx1 (out) = PIN_G10
 
* fpgaTx1 (out) = PIN_G10
 
* fpgaRts1 = U7-44 = PIN_F10
 
* fpgaRts1 = U7-44 = PIN_F10
Line 143: Line 697:
 
* cts2 (in) = PIN_M21
 
* cts2 (in) = PIN_M21
  
=== P4 - SD Card (5CEFA2F23 FPGA pin numbers) ===
+
=== J4 - USB-B B (5CEFA2F23 FPGA Card pin numbers) Serial Port ===
  
* This build only works with SD Cards, not SD/HC or other newer cards.
+
* On-board FT230X FTDI USB to Serial
* These cards are 1 GB or 2 GB in size.
 
  
[[File:SD_Card_Mapping.PNG]]
+
[[File:RETROEP4CE15-Serial.PNG]]
  
* SDCS = U7-57 = PIN_BANK_7A_B15
+
== FPGA Resources ==
* MOSI = U7-58 = PIN_BANK_7A_C15
 
* SCK = U7-59 = PIN_BANK_7A_C16
 
* MISO = U7-60 = PIN_BANK_7A_B16
 
* SD_DETECT - PIN_B12
 
  
=== J1 - I/O Connector (5CEFA2F23 FPGA Card pin numbers) ===
+
* Uses > 80% of the ALMs in Cyclone V 5CEFA2F23I7 part
  
[[File:J1_MAP_FPGA_PINS.PNG]]
+
=== PDP-11/45 ===
  
* J1-50 = GND
+
* No Front Panel
* J1-49 = GND
+
* [[Multicomp_in_a_Box|In MultiComp Box]]
* J1-48 = PIN_M22 = resetbtn
 
* J1-47 = PIN_L22 = n/a
 
* J1-46 = PIN_L18 = tx1
 
* J1-45 = PIN_L19 = rx1
 
* J1-44 = PIN_M18 = rts1
 
* J1-43 = PIN_N19 = cts1
 
* J1-42 = PIN_M21 = n/a
 
* J1-41 = PIN_M20 = n/a
 
* J1-40 = PIN_N20 = xu_sclk
 
* J1-39 = PIN_N21 = xu_mosi
 
* J1-38 = PIN_P16 = xu_miso
 
* J1-37 = PIN_P17 = xu_debug_tx
 
* J1-36 = PIN_T20 = xu_cs
 
* J1-34 = PIN_P22 = greenled[1]
 
* J1-33 = PIN_R21 = greenled[0]
 
* J1-32 = PIN_R22 = greenled[3]
 
* J1-31 = PIN_T22 = greenled[2]
 
* J1-29 = PIN_U20 = greenled[4]
 
* J1-1 = VCC
 
* J1-2 = VCC
 
  
=== J4 - USB-B B (5CEFA2F23 FPGA Card pin numbers) Serial Port ===
+
<pre>
 +
+-------------------------------------------------------------------------------+
 +
; Fitter Summary                                                                ;
 +
+---------------------------------+---------------------------------------------+
 +
; Fitter Status                  ; Successful - Sun May  1 13:02:25 2022      ;
 +
; Quartus Prime Version          ; 21.1.0 Build 842 10/21/2021 SJ Lite Edition ;
 +
; Revision Name                  ; top                                        ;
 +
; Top-level Entity Name          ; top                                        ;
 +
; Family                          ; Cyclone V                                  ;
 +
; Device                          ; 5CEFA2F23I7                                ;
 +
; Timing Models                  ; Final                                      ;
 +
; Logic utilization (in ALMs)    ; 7,797 / 9,430 ( 83 % )                      ;
 +
; Total registers                ; 6002                                        ;
 +
; Total pins                      ; 68 / 224 ( 30 % )                          ;
 +
; Total virtual pins              ; 0                                          ;
 +
; Total block memory bits        ; 180,224 / 1,802,240 ( 10 % )                ;
 +
; Total RAM Blocks                ; 25 / 176 ( 14 % )                          ;
 +
; Total DSP Blocks                ; 1 / 25 ( 4 % )                              ;
 +
; Total HSSI RX PCSs              ; 0                                          ;
 +
; Total HSSI PMA RX Deserializers ; 0                                          ;
 +
; Total HSSI TX PCSs              ; 0                                          ;
 +
; Total HSSI PMA TX Serializers  ; 0                                          ;
 +
; Total PLLs                      ; 1 / 4 ( 25 % )                              ;
 +
; Total DLLs                      ; 0 / 4 ( 0 % )                              ;
 +
+---------------------------------+---------------------------------------------+
 +
</pre>
 +
 
 +
=== PDP-11/70 ===
  
* On-board FT230X FTDI USB to Serial
+
* Front Panel
 +
* [[Multicomp_in_a_Box|In MultiComp Box]]
  
[[File:RETROEP4CE15-Serial.PNG]]
+
<pre>
 +
+-------------------------------------------------------------------------------+
 +
; Fitter Summary                                                                ;
 +
+---------------------------------+---------------------------------------------+
 +
; Fitter Status                  ; Successful - Sat Apr 30 19:30:51 2022      ;
 +
; Quartus Prime Version          ; 21.1.0 Build 842 10/21/2021 SJ Lite Edition ;
 +
; Revision Name                  ; top                                        ;
 +
; Top-level Entity Name          ; top                                        ;
 +
; Family                          ; Cyclone V                                  ;
 +
; Device                          ; 5CEFA2F23I7                                ;
 +
; Timing Models                  ; Final                                      ;
 +
; Logic utilization (in ALMs)    ; 7,809 / 9,430 ( 83 % )                      ;
 +
; Total registers                ; 6016                                        ;
 +
; Total pins                      ; 76 / 224 ( 34 % )                          ;
 +
; Total virtual pins              ; 0                                          ;
 +
; Total block memory bits        ; 180,224 / 1,802,240 ( 10 % )                ;
 +
; Total RAM Blocks                ; 25 / 176 ( 14 % )                          ;
 +
; Total DSP Blocks                ; 1 / 25 ( 4 % )                              ;
 +
; Total HSSI RX PCSs              ; 0                                          ;
 +
; Total HSSI PMA RX Deserializers ; 0                                          ;
 +
; Total HSSI TX PCSs              ; 0                                          ;
 +
; Total HSSI PMA TX Serializers  ; 0                                          ;
 +
; Total PLLs                      ; 1 / 4 ( 25 % )                              ;
 +
; Total DLLs                      ; 0 / 4 ( 0 % )                              ;
 +
+---------------------------------+---------------------------------------------+
 +
</pre>
  
== Resources ==
+
== External Resources ==
  
 
* [https://pdp2011.sytse.net/wordpress/ PDP2011] by Sytse van Slooten
 
* [https://pdp2011.sytse.net/wordpress/ PDP2011] by Sytse van Slooten
** Active as of 2021-02
+
** Active as of 2021-11
 
* [https://github.com/DavidJRichards/pdp2011/ David J Richards PDP-11 Build] - copied and adapted from pdp2011 by Sytse van Slooten
 
* [https://github.com/DavidJRichards/pdp2011/ David J Richards PDP-11 Build] - copied and adapted from pdp2011 by Sytse van Slooten
 
** [https://github.com/DavidJRichards/pdp2011/wiki Wiki]
 
** [https://github.com/DavidJRichards/pdp2011/wiki Wiki]
Line 209: Line 791:
 
** [https://github.com/wfjm/w11/blob/master/doc/w11a_os_guide.md#guide-to-run-operating-system-images-on-w11a-systems Guide to run operating system images on w11a systems]
 
** [https://github.com/wfjm/w11/blob/master/doc/w11a_os_guide.md#guide-to-run-operating-system-images-on-w11a-systems Guide to run operating system images on w11a systems]
 
** [https://github.com/wfjm/w11/blob/master/doc/INSTALL.md Guide to install and build w11a systems, test benches and support software]
 
** [https://github.com/wfjm/w11/blob/master/doc/INSTALL.md Guide to install and build w11a systems, test benches and support software]
 +
* [http://labo.nshimizu.com/pop11.html Naohiko Shimizu's POP-11]
 +
* [http://www.heeltoe.com/download/pdp11/README.html Scalar FPGA PDP-11 in Verilog]
 +
* [https://github.com/aap/fpga11 PDP-11 using PiPDP-11 Front Panel]
 +
** [https://obsolescence.wixsite.com/obsolescence/pidp-11-technical-details The PiDP-11: Technical Details]
  
 
== Programming the FPGA EEPROM (5CEFA2F23 FPGA) ==
 
== Programming the FPGA EEPROM (5CEFA2F23 FPGA) ==
Line 230: Line 816:
 
* Press button near VGA
 
* Press button near VGA
  
== Pin List ==
+
== Pin Lists ==
 +
 
 +
=== Pin List Standalone with Front Panel ===
 +
 
 +
* With [[LEDS-SWITCHES-2]] card
 +
 
 +
{| class="wikitable"
 +
! To
 +
! Direction
 +
! Location
 +
! I/O Standard
 +
! Pull-Up
 +
|-
 +
| clkin
 +
| Input
 +
| PIN_M9
 +
| 3.3-V LVTTL
 +
|
 +
|-
 +
| cts1
 +
| Input
 +
| PIN_B11
 +
| 3.3-V LVTTL
 +
|
 +
|-
 +
| dram_addr[0]
 +
| Output
 +
| PIN_P8
 +
| 3.3-V LVTTL
 +
|
 +
|-
 +
| dram_addr[1]
 +
| Output
 +
| PIN_P7
 +
| 3.3-V LVTTL
 +
|
 +
|-
 +
| dram_addr[10]
 +
| Output
 +
| PIN_R6
 +
| 3.3-V LVTTL
 +
|
 +
|-
 +
| dram_addr[11]
 +
| Output
 +
| PIN_T9
 +
| 3.3-V LVTTL
 +
|
 +
|-
 +
| dram_addr[12]
 +
| Output
 +
| PIN_Y9
 +
| 3.3-V LVTTL
 +
|
 +
|-
 +
| dram_addr[2]
 +
| Output
 +
| PIN_N8
 +
| 3.3-V LVTTL
 +
|
 +
|-
 +
| dram_addr[3]
 +
| Output
 +
| PIN_N6
 +
| 3.3-V LVTTL
 +
|
 +
|-
 +
| dram_addr[4]
 +
| Output
 +
| PIN_U6
 +
| 3.3-V LVTTL
 +
|
 +
|-
 +
| dram_addr[5]
 +
| Output
 +
| PIN_U7
 +
| 3.3-V LVTTL
 +
|
 +
|-
 +
| dram_addr[6]
 +
| Output
 +
| PIN_V6
 +
| 3.3-V LVTTL
 +
|
 +
|-
 +
| dram_addr[7]
 +
| Output
 +
| PIN_U8
 +
| 3.3-V LVTTL
 +
|
 +
|-
 +
| dram_addr[8]
 +
| Output
 +
| PIN_T8
 +
| 3.3-V LVTTL
 +
|
 +
|-
 +
| dram_addr[9]
 +
| Output
 +
| PIN_W8
 +
| 3.3-V LVTTL
 +
|
 +
|-
 +
| dram_ba_0
 +
| Output
 +
| PIN_T7
 +
| 3.3-V LVTTL
 +
|
 +
|-
 +
| dram_ba_1
 +
| Output
 +
| PIN_P9
 +
| 3.3-V LVTTL
 +
|
 +
|-
 +
| dram_cas_n
 +
| Output
 +
| PIN_AA7
 +
| 3.3-V LVTTL
 +
|
 +
|-
 +
| dram_cke
 +
| Output
 +
| PIN_V9
 +
| 3.3-V LVTTL
 +
|
 +
|-
 +
| dram_clk
 +
| Output
 +
| PIN_AB11
 +
| 3.3-V LVTTL
 +
|
 +
|-
 +
| dram_cs_n
 +
| Output
 +
| PIN_AB5
 +
| 3.3-V LVTTL
 +
|
 +
|-
 +
| dram_dq[0]
 +
| Bidir
 +
| PIN_AA12
 +
| 3.3-V LVTTL
 +
|
 +
|-
 +
| dram_dq[1]
 +
| Bidir
 +
| PIN_Y11
 +
| 3.3-V LVTTL
 +
|
 +
|-
 +
| dram_dq[10]
 +
| Bidir
 +
| PIN_U11
 +
| 3.3-V LVTTL
 +
|
 +
|-
 +
| dram_dq[11]
 +
| Bidir
 +
| PIN_R10
 +
| 3.3-V LVTTL
 +
|
 +
|-
 +
| dram_dq[12]
 +
| Bidir
 +
| PIN_R11
 +
| 3.3-V LVTTL
 +
|
 +
|-
 +
| dram_dq[13]
 +
| Bidir
 +
| PIN_U12
 +
| 3.3-V LVTTL
 +
|
 +
|-
 +
| dram_dq[14]
 +
| Bidir
 +
| PIN_R12
 +
| 3.3-V LVTTL
 +
|
 +
|-
 +
| dram_dq[15]
 +
| Bidir
 +
| PIN_P12
 +
| 3.3-V LVTTL
 +
|
 +
|-
 +
| dram_dq[2]
 +
| Bidir
 +
| PIN_AA10
 +
| 3.3-V LVTTL
 +
|
 +
|-
 +
| dram_dq[3]
 +
| Bidir
 +
| PIN_AB10
 +
| 3.3-V LVTTL
 +
|
 +
|-
 +
| dram_dq[4]
 +
| Bidir
 +
| PIN_Y10
 +
| 3.3-V LVTTL
 +
|
 +
|-
 +
| dram_dq[5]
 +
| Bidir
 +
| PIN_AA9
 +
| 3.3-V LVTTL
 +
|
 +
|-
 +
| dram_dq[6]
 +
| Bidir
 +
| PIN_AB8
 +
| 3.3-V LVTTL
 +
|
 +
|-
 +
| dram_dq[7]
 +
| Bidir
 +
| PIN_AA8
 +
| 3.3-V LVTTL
 +
|
 +
|-
 +
| dram_dq[8]
 +
| Bidir
 +
| PIN_U10
 +
| 3.3-V LVTTL
 +
|
 +
|-
 +
| dram_dq[9]
 +
| Bidir
 +
| PIN_T10
 +
| 3.3-V LVTTL
 +
|
 +
|-
 +
| dram_ldqm
 +
| Output
 +
| PIN_AB7
 +
| 3.3-V LVTTL
 +
|
 +
|-
 +
| dram_ras_n
 +
| Output
 +
| PIN_AB6
 +
| 3.3-V LVTTL
 +
|
 +
|-
 +
| dram_udqm
 +
| Output
 +
| PIN_V10
 +
| 3.3-V LVTTL
 +
|
 +
|-
 +
| dram_we_n
 +
| Output
 +
| PIN_W9
 +
| 3.3-V LVTTL
 +
|
 +
|-
 +
| i_PB[1]
 +
| Input
 +
| PIN_W19
 +
| 3.3-V LVTTL
 +
|
 +
|-
 +
| i_PB[2]
 +
| Input
 +
| PIN_U21
 +
| 3.3-V LVTTL
 +
|
 +
|-
 +
| i_PB[3]
 +
| Input
 +
| PIN_R21
 +
| 3.3-V LVTTL
 +
|
 +
|-
 +
| i_PB[4]
 +
| Input
 +
| PIN_T20
 +
| 3.3-V LVTTL
 +
|
 +
|-
 +
| i_PB[5]
 +
| Input
 +
| PIN_N21
 +
| 3.3-V LVTTL
 +
|
 +
|-
 +
| i_PB[6]
 +
| Input
 +
| PIN_M21
 +
| 3.3-V LVTTL
 +
|
 +
|-
 +
| i_PB[7]
 +
| Input
 +
| PIN_L19
 +
| 3.3-V LVTTL
 +
|
 +
|-
 +
| i_PB[8]
 +
| Input
 +
| PIN_M22
 +
| 3.3-V LVTTL
 +
|
 +
|-
 +
| i_SS[1]
 +
| Input
 +
| PIN_V21
 +
| 3.3-V LVTTL
 +
|
 +
|-
 +
| i_SS[2]
 +
| Input
 +
| PIN_V20
 +
| 3.3-V LVTTL
 +
|
 +
|-
 +
| i_SS[3]
 +
| Input
 +
| PIN_T22
 +
| 3.3-V LVTTL
 +
|
 +
|-
 +
| i_SS[4]
 +
| Input
 +
| PIN_P22
 +
| 3.3-V LVTTL
 +
|
 +
|-
 +
| i_SS[5]
 +
| Input
 +
| PIN_P17
 +
| 3.3-V LVTTL
 +
|
 +
|-
 +
| i_SS[6]
 +
| Input
 +
| PIN_N20
 +
| 3.3-V LVTTL
 +
|
 +
|-
 +
| i_SS[7]
 +
| Input
 +
| PIN_N19
 +
| 3.3-V LVTTL
 +
|
 +
|-
 +
| i_SS[8]
 +
| Input
 +
| PIN_L18
 +
| 3.3-V LVTTL
 +
|
 +
|-
 +
| o_LED[1]
 +
| Output
 +
| PIN_U22
 +
| 3.3-V LVTTL
 +
|
 +
|-
 +
| o_LED[2]
 +
| Output
 +
| PIN_U20
 +
| 3.3-V LVTTL
 +
|
 +
|-
 +
| o_LED[3]
 +
| Output
 +
| PIN_R22
 +
| 3.3-V LVTTL
 +
|
 +
|-
 +
| o_LED[4]
 +
| Output
 +
| PIN_T19
 +
| 3.3-V LVTTL
 +
|
 +
|-
 +
| o_LED[5]
 +
| Output
 +
| PIN_P16
 +
| 3.3-V LVTTL
 +
|
 +
|-
 +
| o_LED[6]
 +
| Output
 +
| PIN_M20
 +
| 3.3-V LVTTL
 +
|
 +
|-
 +
| o_LED[7]
 +
| Output
 +
| PIN_M18
 +
| 3.3-V LVTTL
 +
|
 +
|-
 +
| o_LED[8]
 +
| Output
 +
| PIN_L22
 +
| 3.3-V LVTTL
 +
|
 +
|-
 +
| ps2k_c
 +
| Input
 +
| PIN_AA2
 +
| 3.3-V LVTTL
 +
|
 +
|-
 +
| ps2k_d
 +
| Input
 +
| PIN_AA1
 +
| 3.3-V LVTTL
 +
|
 +
|-
 +
| rts1
 +
| Output
 +
| PIN_F10
 +
| 3.3-V LVTTL
 +
|
 +
|-
 +
| rx1
 +
| Input
 +
| PIN_C11
 +
| 3.3-V LVTTL
 +
|
 +
|-
 +
| sdcard_cs
 +
| Output
 +
| PIN_B15
 +
| 3.3-V LVTTL
 +
|
 +
|-
 +
| sdcard_miso
 +
| Input
 +
| PIN_B16
 +
| 3.3-V LVTTL
 +
|
 +
|-
 +
| sdcard_mosi
 +
| Output
 +
| PIN_C15
 +
| 3.3-V LVTTL
 +
|
 +
|-
 +
| sdcard_sclk
 +
| Output
 +
| PIN_C16
 +
| 3.3-V LVTTL
 +
|
 +
|-
 +
| tx1
 +
| Output
 +
| PIN_G10
 +
| 3.3-V LVTTL
 +
|
 +
|-
 +
| vgab[0]
 +
| Output
 +
| PIN_B13
 +
| 3.3-V LVTTL
 +
|
 +
|-
 +
| vgab[1]
 +
| Output
 +
| PIN_A13
 +
| 3.3-V LVTTL
 +
|
 +
|-
 +
| vgag[0]
 +
| Output
 +
| PIN_D13
 +
| 3.3-V LVTTL
 +
|
 +
|-
 +
| vgag[1]
 +
| Output
 +
| PIN_C13
 +
| 3.3-V LVTTL
 +
|
 +
|-
 +
| vgah
 +
| Output
 +
| PIN_A15
 +
| 3.3-V LVTTL
 +
|
 +
|-
 +
| vgar[0]
 +
| Output
 +
| PIN_E12
 +
| 3.3-V LVTTL
 +
|
 +
|-
 +
| vgar[1]
 +
| Output
 +
| PIN_D12
 +
| 3.3-V LVTTL
 +
|
 +
|-
 +
| vgav
 +
| Output
 +
| PIN_A14
 +
| 3.3-V LVTTL
 +
|
 +
|-
 +
| xu_cs
 +
| Output
 +
|
 +
| 3.3-V LVTTL
 +
|
 +
|-
 +
| xu_debug_tx
 +
| Output
 +
|
 +
| 3.3-V LVTTL
 +
|
 +
|-
 +
| xu_miso
 +
| Input
 +
|
 +
| 3.3-V LVTTL
 +
|
 +
|-
 +
| xu_mosi
 +
| Output
 +
|
 +
| 3.3-V LVTTL
 +
|
 +
|-
 +
| xu_sclk
 +
| Output
 +
|
 +
| 3.3-V LVTTL
 +
|
 +
|-
 +
|}
 +
 
 +
=== qsf Standalone file with Front Panel ===
  
 
<pre>
 
<pre>
# Analysis & Synthesis Assignments
 
# ================================
 
 
set_global_assignment -name FAMILY "Cyclone V"
 
set_global_assignment -name FAMILY "Cyclone V"
 +
set_global_assignment -name DEVICE 5CEFA2F23I7
 
set_global_assignment -name TOP_LEVEL_ENTITY top
 
set_global_assignment -name TOP_LEVEL_ENTITY top
set_global_assignment -name EDA_DESIGN_ENTRY_SYNTHESIS_TOOL "Design Compiler"
+
set_global_assignment -name ORIGINAL_QUARTUS_VERSION 9.0
 +
set_global_assignment -name PROJECT_CREATION_TIME_DATE "23:14:32  MARCH 19, 2009"
 +
set_global_assignment -name LAST_QUARTUS_VERSION "21.1.0 Lite Edition"
 +
set_global_assignment -name STRATIX_DEVICE_IO_STANDARD "3.3-V LVTTL"
 +
set_global_assignment -name CYCLONEII_RESERVE_NCEO_AFTER_CONFIGURATION "USE AS REGULAR IO"
 +
set_global_assignment -name RESERVE_ASDO_AFTER_CONFIGURATION "AS INPUT TRI-STATED"
 +
set_global_assignment -name MIN_CORE_JUNCTION_TEMP "-40"
 +
set_global_assignment -name MAX_CORE_JUNCTION_TEMP 100
 +
set_global_assignment -name POWER_PRESET_COOLING_SOLUTION "23 MM HEAT SINK WITH 200 LFPM AIRFLOW"
 +
set_global_assignment -name POWER_BOARD_THERMAL_MODEL "NONE (CONSERVATIVE)"
 +
# Clock
 +
set_location_assignment PIN_M9 -to clkin
 +
# Pushbuttons on LEDS-SWITCHES-2 card
 +
set_location_assignment PIN_M22 -to i_PB[8]
 +
set_location_assignment PIN_L19 -to i_PB[7]
 +
set_location_assignment PIN_M21 -to i_PB[6]
 +
set_location_assignment PIN_N21 -to i_PB[5]
 +
set_location_assignment PIN_T20 -to i_PB[4]
 +
set_location_assignment PIN_R21 -to i_PB[3]
 +
set_location_assignment PIN_U21 -to i_PB[2]
 +
set_location_assignment PIN_W19 -to i_PB[1]
 +
set_location_assignment PIN_L18 -to i_SS[8]
 +
set_location_assignment PIN_N19 -to i_SS[7]
 +
set_location_assignment PIN_N20 -to i_SS[6]
 +
set_location_assignment PIN_P17 -to i_SS[5]
 +
set_location_assignment PIN_P22 -to i_SS[4]
 +
set_location_assignment PIN_T22 -to i_SS[3]
 +
set_location_assignment PIN_V20 -to i_SS[2]
 +
set_location_assignment PIN_V21 -to i_SS[1]
 +
# LEDs on LEDS-SWITCHES-2 card
 +
set_location_assignment PIN_L22 -to o_LED[8]
 +
set_location_assignment PIN_M18 -to o_LED[7]
 +
set_location_assignment PIN_M20 -to o_LED[6]
 +
set_location_assignment PIN_P16 -to o_LED[5]
 +
set_location_assignment PIN_T19 -to o_LED[4]
 +
set_location_assignment PIN_R22 -to o_LED[3]
 +
set_location_assignment PIN_U20 -to o_LED[2]
 +
set_location_assignment PIN_U22 -to o_LED[1]
 +
# SDRAM
 +
set_location_assignment PIN_Y9 -to dram_addr[12]
 +
set_location_assignment PIN_T9 -to dram_addr[11]
 +
set_location_assignment PIN_R6 -to dram_addr[10]
 +
set_location_assignment PIN_W8 -to dram_addr[9]
 +
set_location_assignment PIN_T8 -to dram_addr[8]
 +
set_location_assignment PIN_U8 -to dram_addr[7]
 +
set_location_assignment PIN_V6 -to dram_addr[6]
 +
set_location_assignment PIN_U7 -to dram_addr[5]
 +
set_location_assignment PIN_U6 -to dram_addr[4]
 +
set_location_assignment PIN_N6 -to dram_addr[3]
 +
set_location_assignment PIN_N8 -to dram_addr[2]
 +
set_location_assignment PIN_P7 -to dram_addr[1]
 +
set_location_assignment PIN_P8 -to dram_addr[0]
 +
set_location_assignment PIN_P9 -to dram_ba_1
 +
set_location_assignment PIN_T7 -to dram_ba_0
 +
set_location_assignment PIN_AA7 -to dram_cas_n
 +
set_location_assignment PIN_V9 -to dram_cke
 +
set_location_assignment PIN_AB11 -to dram_clk
 +
set_location_assignment PIN_AB5 -to dram_cs_n
 +
set_location_assignment PIN_P12 -to dram_dq[15]
 +
set_location_assignment PIN_R12 -to dram_dq[14]
 +
set_location_assignment PIN_U12 -to dram_dq[13]
 +
set_location_assignment PIN_R11 -to dram_dq[12]
 +
set_location_assignment PIN_R10 -to dram_dq[11]
 +
set_location_assignment PIN_U11 -to dram_dq[10]
 +
set_location_assignment PIN_T10 -to dram_dq[9]
 +
set_location_assignment PIN_U10 -to dram_dq[8]
 +
set_location_assignment PIN_AA8 -to dram_dq[7]
 +
set_location_assignment PIN_AB8 -to dram_dq[6]
 +
set_location_assignment PIN_AA9 -to dram_dq[5]
 +
set_location_assignment PIN_Y10 -to dram_dq[4]
 +
set_location_assignment PIN_AB10 -to dram_dq[3]
 +
set_location_assignment PIN_AA10 -to dram_dq[2]
 +
set_location_assignment PIN_Y11 -to dram_dq[1]
 +
set_location_assignment PIN_AA12 -to dram_dq[0]
 +
set_location_assignment PIN_V10 -to dram_udqm
 +
set_location_assignment PIN_AB7 -to dram_ldqm
 +
set_location_assignment PIN_AB6 -to dram_ras_n
 +
set_location_assignment PIN_W9 -to dram_we_n
 +
# Serial port (USB-to-Serial)
 +
set_location_assignment PIN_C11 -to rx1
 +
set_location_assignment PIN_G10 -to tx1
 +
set_location_assignment PIN_F10 -to rts1
 +
set_location_assignment PIN_B11 -to cts1
 +
# Second serial port
 +
# SD Card
 +
set_location_assignment PIN_C16 -to sdcard_sclk
 +
set_location_assignment PIN_B15 -to sdcard_cs
 +
set_location_assignment PIN_B16 -to sdcard_miso
 +
set_location_assignment PIN_C15 -to sdcard_mosi
 +
# Ethernet
 +
# PS/2 Keyboard
 +
set_location_assignment PIN_AA2 -to ps2k_c
 +
set_location_assignment PIN_AA1 -to ps2k_d
 +
# Video
 +
set_location_assignment PIN_E12 -to vgar[0]
 +
set_location_assignment PIN_D12 -to vgar[1]
 +
set_location_assignment PIN_B13 -to vgab[0]
 +
set_location_assignment PIN_A13 -to vgab[1]
 +
set_location_assignment PIN_D13 -to vgag[0]
 +
set_location_assignment PIN_C13 -to vgag[1]
 +
set_location_assignment PIN_A15 -to vgah
 +
set_location_assignment PIN_A14 -to vgav
 +
</pre>
  
# Fitter Assignments
+
=== Pin List Standalone ===
# ==================
+
 
 +
=== qsf file Standalone ===
 +
 
 +
<pre>
 +
set_global_assignment -name FAMILY "Cyclone V"
 
set_global_assignment -name DEVICE 5CEFA2F23I7
 
set_global_assignment -name DEVICE 5CEFA2F23I7
 +
set_global_assignment -name TOP_LEVEL_ENTITY top
 +
set_global_assignment -name ORIGINAL_QUARTUS_VERSION 9.0
 +
set_global_assignment -name PROJECT_CREATION_TIME_DATE "23:14:32  MARCH 19, 2009"
 +
set_global_assignment -name LAST_QUARTUS_VERSION "21.1.0 Lite Edition"
 
set_global_assignment -name STRATIX_DEVICE_IO_STANDARD "3.3-V LVTTL"
 
set_global_assignment -name STRATIX_DEVICE_IO_STANDARD "3.3-V LVTTL"
set_global_assignment -name CRC_ERROR_OPEN_DRAIN OFF
 
 
set_global_assignment -name CYCLONEII_RESERVE_NCEO_AFTER_CONFIGURATION "USE AS REGULAR IO"
 
set_global_assignment -name CYCLONEII_RESERVE_NCEO_AFTER_CONFIGURATION "USE AS REGULAR IO"
set_global_assignment -name FORCE_CONFIGURATION_VCCIO ON
+
set_global_assignment -name RESERVE_ASDO_AFTER_CONFIGURATION "AS INPUT TRI-STATED"
 
 
# Pin & Location Assignments
 
# ==========================
 
 
 
# Clock and reset
 
 
set_location_assignment PIN_M9 -to clkin
 
set_location_assignment PIN_M9 -to clkin
 
set_location_assignment PIN_M22 -to resetbtn
 
set_location_assignment PIN_M22 -to resetbtn
 
set_instance_assignment -name WEAK_PULL_UP_RESISTOR ON -to resetbtn
 
set_instance_assignment -name WEAK_PULL_UP_RESISTOR ON -to resetbtn
# Control switches - Jumpers on front edge
+
# Control switches
set_location_assignment PIN_L17 -to sw[0]
+
# Jumpers on front edge
set_instance_assignment -name WEAK_PULL_UP_RESISTOR ON -to sw[0]
 
set_location_assignment PIN_K17 -to sw[1]
 
set_instance_assignment -name WEAK_PULL_UP_RESISTOR ON -to sw[1]
 
set_location_assignment PIN_K22 -to sw[2]
 
set_instance_assignment -name WEAK_PULL_UP_RESISTOR ON -to sw[2]
 
set_location_assignment PIN_K21 -to sw[3]
 
set_instance_assignment -name WEAK_PULL_UP_RESISTOR ON -to sw[3]
 
set_location_assignment PIN_M16 -to sw[4]
 
set_instance_assignment -name WEAK_PULL_UP_RESISTOR ON -to sw[4]
 
set_location_assignment PIN_N16 -to sw[5]
 
set_instance_assignment -name WEAK_PULL_UP_RESISTOR ON -to sw[5]
 
# LEDs
 
set_location_assignment PIN_R21 -to greenled[0]
 
set_location_assignment PIN_P22 -to greenled[1]
 
set_location_assignment PIN_T22 -to greenled[2]
 
set_location_assignment PIN_R22 -to greenled[3]
 
set_location_assignment PIN_U20 -to greenled[4]
 
 
# SDRAM
 
# SDRAM
 
set_location_assignment PIN_Y9 -to dram_addr[12]
 
set_location_assignment PIN_Y9 -to dram_addr[12]
Line 335: Line 1,544:
 
set_location_assignment PIN_AA1 -to ps2k_d
 
set_location_assignment PIN_AA1 -to ps2k_d
 
# Video
 
# Video
 +
set_location_assignment PIN_A15 -to vgah
 +
set_location_assignment PIN_A14 -to vgav
 +
 +
set_global_assignment -name PARTITION_NETLIST_TYPE SOURCE -section_id Top
 +
set_global_assignment -name PARTITION_FITTER_PRESERVATION_LEVEL PLACEMENT_AND_ROUTING -section_id Top
 +
set_global_assignment -name PARTITION_COLOR 16764057 -section_id Top
 +
 +
set_global_assignment -name MIN_CORE_JUNCTION_TEMP "-40"
 +
set_global_assignment -name MAX_CORE_JUNCTION_TEMP 100
 +
set_global_assignment -name POWER_PRESET_COOLING_SOLUTION "23 MM HEAT SINK WITH 200 LFPM AIRFLOW"
 +
set_global_assignment -name POWER_BOARD_THERMAL_MODEL "NONE (CONSERVATIVE)"
 
set_location_assignment PIN_E12 -to vgar[0]
 
set_location_assignment PIN_E12 -to vgar[0]
 
set_location_assignment PIN_D12 -to vgar[1]
 
set_location_assignment PIN_D12 -to vgar[1]
Line 341: Line 1,561:
 
set_location_assignment PIN_D13 -to vgag[0]
 
set_location_assignment PIN_D13 -to vgag[0]
 
set_location_assignment PIN_C13 -to vgag[1]
 
set_location_assignment PIN_C13 -to vgag[1]
 +
set_location_assignment PIN_L17 -to sw[0]
 +
set_location_assignment PIN_K17 -to sw[1]
 +
set_location_assignment PIN_K22 -to sw[2]
 +
set_location_assignment PIN_K21 -to sw[3]
 +
set_location_assignment PIN_M16 -to sw[4]
 +
set_location_assignment PIN_N16 -to sw[5]
 +
set_location_assignment PIN_R21 -to greenled[0]
 +
set_location_assignment PIN_P22 -to greenled[1]
 +
set_location_assignment PIN_T22 -to greenled[2]
 +
set_location_assignment PIN_R22 -to greenled[3]
 +
set_location_assignment PIN_U20 -to greenled[4]
 +
set_global_assignment -name VHDL_FILE ../vgacr.vhd
 +
set_global_assignment -name VHDL_FILE ../vga.vhd
 +
set_global_assignment -name VHDL_FILE ../vt.vhd
 +
set_global_assignment -name VHDL_FILE ../ps2.vhd
 +
set_global_assignment -name VHDL_FILE ../vgafont.vhd
 +
set_global_assignment -name VHDL_FILE ../vtbrt42.vhd
 +
set_global_assignment -name VHDL_FILE ../sdspi.vhd
 +
set_global_assignment -name VHDL_FILE ../mnckw.vhd
 +
set_global_assignment -name VHDL_FILE ../mncdo.vhd
 +
set_global_assignment -name VHDL_FILE ../mncdi.vhd
 +
set_global_assignment -name VHDL_FILE ../mncad.vhd
 +
set_global_assignment -name VHDL_FILE ../mncaa.vhd
 +
set_global_assignment -name VHDL_FILE ../m9312h47.vhd
 +
set_global_assignment -name VHDL_FILE ../m9312l47.vhd
 +
set_global_assignment -name VHDL_FILE ../dr11c.vhd
 +
set_global_assignment -name VHDL_FILE ../panelos.vhd
 +
set_global_assignment -name VHDL_FILE ../paneldriver.vhd
 +
set_global_assignment -name VHDL_FILE ../paneldb.vhd
 +
set_global_assignment -name VHDL_FILE ../xubrt45.vhd
 +
set_global_assignment -name VHDL_FILE ../xubm.vhd
 +
set_global_assignment -name VHDL_FILE ../xubl.vhd
 +
set_global_assignment -name VHDL_FILE ../xu.vhd
 +
set_global_assignment -name VHDL_FILE ../rh11.vhd
 +
set_global_assignment -name VHDL_FILE ../kl11.vhd
 +
set_global_assignment -name VHDL_FILE ../rk11.vhd
 +
set_global_assignment -name VHDL_FILE ../unibus.vhd
 +
set_global_assignment -name VHDL_FILE ../cr.vhd
 +
set_global_assignment -name VHDL_FILE ../rl11.vhd
 +
set_global_assignment -name VHDL_FILE ../mmu.vhd
 +
set_global_assignment -name VHDL_FILE ../kw11l.vhd
 +
set_global_assignment -name VHDL_FILE ../fpuregs.vhd
 +
set_global_assignment -name VHDL_FILE ../csdr.vhd
 +
set_global_assignment -name VHDL_FILE ../cpuregs.vhd
 +
set_global_assignment -name VHDL_FILE ../cpu.vhd
 +
set_global_assignment -name VHDL_FILE top.vhd
 +
set_global_assignment -name VHDL_FILE ssegdecoder.vhd
 +
set_global_assignment -name CDF_FILE top.cdf
 +
set_global_assignment -name QIP_FILE pll.qip
 +
set_instance_assignment -name PARTITION_HIERARCHY root_partition -to | -section_id Top
 +
</pre>
 +
 +
=== Pin List in MultiComp Box ===
 +
 +
{| class="wikitable"
 +
! To
 +
! Direction
 +
! Location
 +
! Pull-Up
 +
|-
 +
| clkin
 +
| Input
 +
| PIN_M9
 +
|
 +
|-
 +
| cts1
 +
| Input
 +
| PIN_B11
 +
| on
 +
|-
 +
| dram_addr[12]
 +
| Output
 +
| PIN_Y9
 +
|
 +
|-
 +
| dram_addr[11]
 +
| Output
 +
| PIN_T9
 +
|
 +
|-
 +
| dram_addr[10]
 +
| Output
 +
| PIN_R6
 +
|
 +
|-
 +
| dram_addr[9]
 +
| Output
 +
| PIN_W8
 +
|
 +
|-
 +
| dram_addr[8]
 +
| Output
 +
| PIN_T8
 +
|
 +
|-
 +
| dram_addr[7]
 +
| Output
 +
| PIN_U8
 +
|
 +
|-
 +
| dram_addr[6]
 +
| Output
 +
| PIN_V6
 +
|
 +
|-
 +
| dram_addr[5]
 +
| Output
 +
| PIN_U7
 +
|
 +
|-
 +
| dram_addr[4]
 +
| Output
 +
| PIN_U6
 +
|
 +
|-
 +
| dram_addr[3]
 +
| Output
 +
| PIN_N6
 +
|
 +
|-
 +
| dram_addr[2]
 +
| Output
 +
| PIN_N8
 +
|
 +
|-
 +
| dram_addr[1]
 +
| Output
 +
| PIN_P7
 +
|
 +
|-
 +
| dram_addr[0]
 +
| Output
 +
| PIN_P8
 +
|
 +
|-
 +
| dram_ba_0
 +
| Output
 +
| PIN_T7
 +
|
 +
|-
 +
| dram_ba_1
 +
| Output
 +
| PIN_P9
 +
|
 +
|-
 +
| dram_cas_n
 +
| Output
 +
| PIN_AA7
 +
|
 +
|-
 +
| dram_cke
 +
| Output
 +
| PIN_V9
 +
|
 +
|-
 +
| dram_clk
 +
| Output
 +
| PIN_AB11
 +
|
 +
|-
 +
| dram_cs_n
 +
| Output
 +
| PIN_AB5
 +
|
 +
|-
 +
| dram_dq[15]
 +
| Bidir
 +
| PIN_P12
 +
|
 +
|-
 +
| dram_dq[14]
 +
| Bidir
 +
| PIN_R12
 +
|
 +
|-
 +
| dram_dq[13]
 +
| Bidir
 +
| PIN_U12
 +
|
 +
|-
 +
| dram_dq[12]
 +
| Bidir
 +
| PIN_R11
 +
|
 +
|-
 +
| dram_dq[11]
 +
| Bidir
 +
| PIN_R10
 +
|
 +
|-
 +
| dram_dq[10]
 +
| Bidir
 +
| PIN_U11
 +
|
 +
|-
 +
| dram_dq[9]
 +
| Bidir
 +
| PIN_T10
 +
|
 +
|-
 +
| dram_dq[8]
 +
| Bidir
 +
| PIN_U10
 +
|
 +
|-
 +
| dram_dq[7]
 +
| Bidir
 +
| PIN_AA8
 +
|
 +
|-
 +
| dram_dq[6]
 +
| Bidir
 +
| PIN_AB8
 +
|
 +
|-
 +
| dram_dq[5]
 +
| Bidir
 +
| PIN_AA9
 +
|
 +
|-
 +
| dram_dq[4]
 +
| Bidir
 +
| PIN_Y10
 +
|
 +
|-
 +
| dram_dq[3]
 +
| Bidir
 +
| PIN_AB10
 +
|
 +
|-
 +
| dram_dq[2]
 +
| Bidir
 +
| PIN_AA10
 +
|
 +
|-
 +
| dram_dq[1]
 +
| Bidir
 +
| PIN_Y11
 +
|
 +
|-
 +
| dram_dq[0]
 +
| Bidir
 +
| PIN_AA12
 +
|
 +
|-
 +
| dram_ldqm
 +
| Output
 +
| PIN_AB7
 +
|
 +
|-
 +
| dram_ras_n
 +
| Output
 +
| PIN_AB6
 +
|
 +
|-
 +
| dram_udqm
 +
| Output
 +
| PIN_V10
 +
|
 +
|-
 +
| dram_we_n
 +
| Output
 +
| PIN_W9
 +
|
 +
|-
 +
| i_PB[8]
 +
| Input
 +
| PIN_N16
 +
| on
 +
|-
 +
| i_PB[7]
 +
| Input
 +
| PIN_Y20
 +
| on
 +
|-
 +
| i_PB[6]
 +
| Input
 +
| PIN_M21
 +
| on
 +
|-
 +
| i_PB[5]
 +
| Input
 +
| PIN_N21
 +
| on
 +
|-
 +
| i_PB[4]
 +
| Input
 +
| PIN_T20
 +
| on
 +
|-
 +
| i_PB[3]
 +
| Input
 +
| PIN_R21
 +
| on
 +
|-
 +
| i_PB[2]
 +
| Input
 +
| PIN_U21
 +
| on
 +
|-
 +
| i_PB[1]
 +
| Input
 +
| PIN_W19
 +
| on
 +
|-
 +
| i_SS[8]
 +
| Input
 +
| PIN_P22
 +
| on
 +
|-
 +
| i_SS[7]
 +
| Input
 +
| PIN_N19
 +
| on
 +
|-
 +
| i_SS[6]
 +
| Input
 +
| PIN_N20
 +
| on
 +
|-
 +
| i_SS[5]
 +
| Input
 +
| PIN_M16
 +
| on
 +
|-
 +
| i_SS[4]
 +
| Input
 +
| PIN_K21
 +
| on
 +
|-
 +
| i_SS[3]
 +
| Input
 +
| PIN_K22
 +
| on
 +
|-
 +
| i_SS[2]
 +
| Input
 +
| PIN_K17
 +
| on
 +
|-
 +
| i_SS[1]
 +
| Input
 +
| PIN_L17
 +
| on
 +
|-
 +
| o_LED[8]
 +
| Output
 +
| PIN_P17
 +
|
 +
|-
 +
| o_LED[7]
 +
| Output
 +
| PIN_M18
 +
|
 +
|-
 +
| o_LED[6]
 +
| Output
 +
| PIN_M20
 +
|
 +
|-
 +
| o_LED[5]
 +
| Output
 +
| PIN_P16
 +
|
 +
|-
 +
| o_LED[4]
 +
| Output
 +
| PIN_T19
 +
|
 +
|-
 +
| o_LED[3]
 +
| Output
 +
| PIN_R22
 +
|
 +
|-
 +
| o_LED[2]
 +
| Output
 +
| PIN_U20
 +
|
 +
|-
 +
| o_LED[1]
 +
| Output
 +
| PIN_U22
 +
|
 +
|-
 +
| ps2k_c
 +
| Input
 +
| PIN_AA2
 +
| on
 +
|-
 +
| ps2k_d
 +
| Input
 +
| PIN_AA1
 +
| on
 +
|-
 +
| rts1
 +
| Output
 +
| PIN_F10
 +
|
 +
|-
 +
| rx1
 +
| Input
 +
| PIN_C11
 +
| on
 +
|-
 +
| sdcard_cs
 +
| Output
 +
| PIN_M22
 +
|
 +
|-
 +
| sdcard_miso
 +
| Input
 +
| PIN_L18
 +
| on
 +
|-
 +
| sdcard_mosi
 +
| Output
 +
| PIN_L22
 +
|
 +
|-
 +
| sdcard_sclk
 +
| Output
 +
| PIN_L19
 +
|
 +
|-
 +
| tx1
 +
| Output
 +
| PIN_G10
 +
|
 +
|-
 +
| vgab[1]
 +
| Output
 +
| PIN_A13
 +
|
 +
|-
 +
| vgab[0]
 +
| Output
 +
| PIN_B13
 +
|
 +
|-
 +
| vgag[1]
 +
| Output
 +
| PIN_C13
 +
|
 +
|-
 +
| vgag[0]
 +
| Output
 +
| PIN_D13
 +
|
 +
|-
 +
| vgah
 +
| Output
 +
| PIN_A15
 +
|
 +
|-
 +
| vgar[1]
 +
| Output
 +
| PIN_D12
 +
|
 +
|-
 +
| vgar[0]
 +
| Output
 +
| PIN_E12
 +
|
 +
|-
 +
| vgav
 +
| Output
 +
| PIN_A14
 +
|
 +
|-
 +
| xu_cs
 +
| Output
 +
| PIN_AB22
 +
|
 +
|-
 +
| xu_debug_tx
 +
| Output
 +
| PIN_AA22
 +
|
 +
|-
 +
| xu_miso
 +
| Input
 +
| PIN_Y22
 +
| on
 +
|-
 +
| xu_mosi
 +
| Output
 +
| PIN_V20
 +
|
 +
|-
 +
| xu_sclk
 +
| Output
 +
| PIN_T22
 +
|
 +
|-
 +
|}
 +
 +
=== qsf file in MultiComp Box ===
 +
 +
<pre>
 +
set_global_assignment -name FAMILY "Cyclone V"
 +
set_global_assignment -name DEVICE 5CEFA2F23I7
 +
set_global_assignment -name TOP_LEVEL_ENTITY top
 +
set_global_assignment -name ORIGINAL_QUARTUS_VERSION 9.0
 +
set_global_assignment -name PROJECT_CREATION_TIME_DATE "23:14:32  MARCH 19, 2009"
 +
set_global_assignment -name LAST_QUARTUS_VERSION "21.1.0 Lite Edition"
 +
set_global_assignment -name STRATIX_DEVICE_IO_STANDARD "3.3-V LVTTL"
 +
set_global_assignment -name CYCLONEII_RESERVE_NCEO_AFTER_CONFIGURATION "USE AS REGULAR IO"
 +
set_global_assignment -name RESERVE_ASDO_AFTER_CONFIGURATION "AS INPUT TRI-STATED"
 +
set_global_assignment -name PARTITION_NETLIST_TYPE SOURCE -section_id Top
 +
set_global_assignment -name PARTITION_FITTER_PRESERVATION_LEVEL PLACEMENT_AND_ROUTING -section_id Top
 +
set_global_assignment -name PARTITION_COLOR 16764057 -section_id Top
 +
set_global_assignment -name MIN_CORE_JUNCTION_TEMP "-40"
 +
set_global_assignment -name MAX_CORE_JUNCTION_TEMP 100
 +
set_global_assignment -name POWER_PRESET_COOLING_SOLUTION "23 MM HEAT SINK WITH 200 LFPM AIRFLOW"
 +
set_global_assignment -name POWER_BOARD_THERMAL_MODEL "NONE (CONSERVATIVE)"
 +
# Clock
 +
set_location_assignment PIN_M9 -to clkin
 +
# Serial port (USB-to-Serial)
 +
set_location_assignment PIN_C11 -to rx1
 +
set_location_assignment PIN_G10 -to tx1
 +
set_location_assignment PIN_F10 -to rts1
 +
set_location_assignment PIN_B11 -to cts1
 +
set_instance_assignment -name WEAK_PULL_UP_RESISTOR ON -to cts1
 +
set_instance_assignment -name WEAK_PULL_UP_RESISTOR ON -to rx1
 +
# Second serial port
 +
# SD Card
 +
set_location_assignment PIN_L19 -to sdcard_sclk
 +
set_location_assignment PIN_M22 -to sdcard_cs
 +
set_location_assignment PIN_L18 -to sdcard_miso
 +
set_instance_assignment -name WEAK_PULL_UP_RESISTOR ON -to sdcard_miso
 +
set_location_assignment PIN_L22 -to sdcard_mosi
 +
# PS/2 Keyboard
 +
set_location_assignment PIN_AA2 -to ps2k_c
 +
set_location_assignment PIN_AA1 -to ps2k_d
 +
set_instance_assignment -name WEAK_PULL_UP_RESISTOR ON -to ps2k_c
 +
set_instance_assignment -name WEAK_PULL_UP_RESISTOR ON -to ps2k_d
 +
# Video
 
set_location_assignment PIN_A15 -to vgah
 
set_location_assignment PIN_A15 -to vgah
 
set_location_assignment PIN_A14 -to vgav
 
set_location_assignment PIN_A14 -to vgav
 +
set_location_assignment PIN_E12 -to vgar[0]
 +
set_location_assignment PIN_D12 -to vgar[1]
 +
set_location_assignment PIN_B13 -to vgab[0]
 +
set_location_assignment PIN_A13 -to vgab[1]
 +
set_location_assignment PIN_D13 -to vgag[0]
 +
set_location_assignment PIN_C13 -to vgag[1]
 +
# LEDs
 +
set_location_assignment PIN_U22 -to o_LED[1]
 +
set_location_assignment PIN_R22 -to o_LED[3]
 +
set_location_assignment PIN_U20 -to o_LED[2]
 +
set_location_assignment PIN_P17 -to o_LED[8]
 +
set_location_assignment PIN_M18 -to o_LED[7]
 +
set_location_assignment PIN_M20 -to o_LED[6]
 +
set_location_assignment PIN_P16 -to o_LED[5]
 +
set_location_assignment PIN_T19 -to o_LED[4]
 +
# Slide Switches
 +
set_location_assignment PIN_L17 -to i_SS[1]
 +
set_location_assignment PIN_K17 -to i_SS[2]
 +
set_location_assignment PIN_K22 -to i_SS[3]
 +
set_location_assignment PIN_K21 -to i_SS[4]
 +
set_location_assignment PIN_M16 -to i_SS[5]
 +
set_location_assignment PIN_N20 -to i_SS[6]
 +
set_location_assignment PIN_N19 -to i_SS[7]
 +
set_location_assignment PIN_P22 -to i_SS[8]
 +
set_instance_assignment -name WEAK_PULL_UP_RESISTOR ON -to i_SS[8]
 +
set_instance_assignment -name WEAK_PULL_UP_RESISTOR ON -to i_SS[7]
 +
set_instance_assignment -name WEAK_PULL_UP_RESISTOR ON -to i_SS[6]
 +
set_instance_assignment -name WEAK_PULL_UP_RESISTOR ON -to i_SS[5]
 +
set_instance_assignment -name WEAK_PULL_UP_RESISTOR ON -to i_SS[4]
 +
set_instance_assignment -name WEAK_PULL_UP_RESISTOR ON -to i_SS[3]
 +
set_instance_assignment -name WEAK_PULL_UP_RESISTOR ON -to i_SS[2]
 +
set_instance_assignment -name WEAK_PULL_UP_RESISTOR ON -to i_SS[1]
 +
set_instance_assignment -name WEAK_PULL_UP_RESISTOR ON -to i_SS
 +
# Pushbuttons
 +
set_location_assignment PIN_W19 -to i_PB[1]
 +
set_location_assignment PIN_U21 -to i_PB[2]
 +
set_location_assignment PIN_R21 -to i_PB[3]
 +
set_location_assignment PIN_T20 -to i_PB[4]
 +
set_location_assignment PIN_N21 -to i_PB[5]
 +
set_location_assignment PIN_M21 -to i_PB[6]
 +
set_location_assignment PIN_Y20 -to i_PB[7]
 +
set_location_assignment PIN_N16 -to i_PB[8]
 +
set_instance_assignment -name WEAK_PULL_UP_RESISTOR ON -to i_PB[1]
 +
set_instance_assignment -name WEAK_PULL_UP_RESISTOR ON -to i_PB[2]
 +
set_instance_assignment -name WEAK_PULL_UP_RESISTOR ON -to i_PB[3]
 +
set_instance_assignment -name WEAK_PULL_UP_RESISTOR ON -to i_PB[4]
 +
set_instance_assignment -name WEAK_PULL_UP_RESISTOR ON -to i_PB[5]
 +
set_instance_assignment -name WEAK_PULL_UP_RESISTOR ON -to i_PB[6]
 +
set_instance_assignment -name WEAK_PULL_UP_RESISTOR ON -to i_PB[7]
 +
set_instance_assignment -name WEAK_PULL_UP_RESISTOR ON -to i_PB[8]
 +
# Ethernet
 +
set_location_assignment PIN_T22 -to xu_sclk
 +
set_location_assignment PIN_V20 -to xu_mosi
 +
set_location_assignment PIN_Y22 -to xu_miso
 +
set_location_assignment PIN_AA22 -to xu_debug_tx
 +
set_location_assignment PIN_AB22 -to xu_cs
 +
set_instance_assignment -name WEAK_PULL_UP_RESISTOR ON -to xu_miso
 +
# SDRAM
 +
set_location_assignment PIN_Y9 -to dram_addr[12]
 +
set_location_assignment PIN_T9 -to dram_addr[11]
 +
set_location_assignment PIN_R6 -to dram_addr[10]
 +
set_location_assignment PIN_W8 -to dram_addr[9]
 +
set_location_assignment PIN_T8 -to dram_addr[8]
 +
set_location_assignment PIN_U8 -to dram_addr[7]
 +
set_location_assignment PIN_V6 -to dram_addr[6]
 +
set_location_assignment PIN_U7 -to dram_addr[5]
 +
set_location_assignment PIN_U6 -to dram_addr[4]
 +
set_location_assignment PIN_N6 -to dram_addr[3]
 +
set_location_assignment PIN_N8 -to dram_addr[2]
 +
set_location_assignment PIN_P7 -to dram_addr[1]
 +
set_location_assignment PIN_P8 -to dram_addr[0]
 +
set_location_assignment PIN_P9 -to dram_ba_1
 +
set_location_assignment PIN_T7 -to dram_ba_0
 +
set_location_assignment PIN_AA7 -to dram_cas_n
 +
set_location_assignment PIN_V9 -to dram_cke
 +
set_location_assignment PIN_AB11 -to dram_clk
 +
set_location_assignment PIN_AB5 -to dram_cs_n
 +
set_location_assignment PIN_P12 -to dram_dq[15]
 +
set_location_assignment PIN_R12 -to dram_dq[14]
 +
set_location_assignment PIN_U12 -to dram_dq[13]
 +
set_location_assignment PIN_R11 -to dram_dq[12]
 +
set_location_assignment PIN_R10 -to dram_dq[11]
 +
set_location_assignment PIN_U11 -to dram_dq[10]
 +
set_location_assignment PIN_T10 -to dram_dq[9]
 +
set_location_assignment PIN_U10 -to dram_dq[8]
 +
set_location_assignment PIN_AA8 -to dram_dq[7]
 +
set_location_assignment PIN_AB8 -to dram_dq[6]
 +
set_location_assignment PIN_AA9 -to dram_dq[5]
 +
set_location_assignment PIN_Y10 -to dram_dq[4]
 +
set_location_assignment PIN_AB10 -to dram_dq[3]
 +
set_location_assignment PIN_AA10 -to dram_dq[2]
 +
set_location_assignment PIN_Y11 -to dram_dq[1]
 +
set_location_assignment PIN_AA12 -to dram_dq[0]
 +
set_location_assignment PIN_V10 -to dram_udqm
 +
set_location_assignment PIN_AB7 -to dram_ldqm
 +
set_location_assignment PIN_AB6 -to dram_ras_n
 +
set_location_assignment PIN_W9 -to dram_we_n
 +
#
 +
set_global_assignment -name VHDL_FILE ../vgacr.vhd
 +
set_global_assignment -name VHDL_FILE ../vga.vhd
 +
set_global_assignment -name VHDL_FILE ../vt.vhd
 +
set_global_assignment -name VHDL_FILE ../ps2.vhd
 +
set_global_assignment -name VHDL_FILE ../vgafont.vhd
 +
set_global_assignment -name VHDL_FILE ../vtbrt42.vhd
 +
set_global_assignment -name VHDL_FILE ../sdspi.vhd
 +
set_global_assignment -name VHDL_FILE ../mnckw.vhd
 +
set_global_assignment -name VHDL_FILE ../mncdo.vhd
 +
set_global_assignment -name VHDL_FILE ../mncdi.vhd
 +
set_global_assignment -name VHDL_FILE ../mncad.vhd
 +
set_global_assignment -name VHDL_FILE ../mncaa.vhd
 +
set_global_assignment -name VHDL_FILE ../m9312h47.vhd
 +
set_global_assignment -name VHDL_FILE ../m9312l47.vhd
 +
set_global_assignment -name VHDL_FILE ../dr11c.vhd
 +
set_global_assignment -name VHDL_FILE ../panelos.vhd
 +
set_global_assignment -name VHDL_FILE ../paneldriver.vhd
 +
set_global_assignment -name VHDL_FILE ../paneldb.vhd
 +
set_global_assignment -name VHDL_FILE ../xubrt45.vhd
 +
set_global_assignment -name VHDL_FILE ../xubm.vhd
 +
set_global_assignment -name VHDL_FILE ../xubl.vhd
 +
set_global_assignment -name VHDL_FILE ../xu.vhd
 +
set_global_assignment -name VHDL_FILE ../rh11.vhd
 +
set_global_assignment -name VHDL_FILE ../kl11.vhd
 +
set_global_assignment -name VHDL_FILE ../rk11.vhd
 +
set_global_assignment -name VHDL_FILE ../unibus.vhd
 +
set_global_assignment -name VHDL_FILE ../cr.vhd
 +
set_global_assignment -name VHDL_FILE ../rl11.vhd
 +
set_global_assignment -name VHDL_FILE ../mmu.vhd
 +
set_global_assignment -name VHDL_FILE ../kw11l.vhd
 +
set_global_assignment -name VHDL_FILE ../fpuregs.vhd
 +
set_global_assignment -name VHDL_FILE ../csdr.vhd
 +
set_global_assignment -name VHDL_FILE ../cpuregs.vhd
 +
set_global_assignment -name VHDL_FILE ../cpu.vhd
 +
set_global_assignment -name VHDL_FILE top.vhd
 +
set_global_assignment -name VHDL_FILE ssegdecoder.vhd
 +
set_global_assignment -name CDF_FILE top.cdf
 +
set_global_assignment -name QIP_FILE pll.qip
 +
set_instance_assignment -name PARTITION_HIERARCHY root_partition -to | -section_id Top
 
</pre>
 
</pre>

Latest revision as of 11:35, 8 August 2022

PDP-11 FrontPanel P512-cropped-720px.jpg

Overview

Sytse van Slooten's website describes his PDP2011 as

a re-creation of the well-known series of PDP-11 computer systems in VHDL. Everything that is needed to run a PDP-11 system is included; you can run a complete Unibus PDP-11 system with console, disks and other peripherals on a simple low-cost FPGA development board. The original V5-V7 versions of Unix, BSD 2.11, and the original DEC operating systems for the PDP-11 work.

Highlights

  • You can configure PDP2011 to be 11/20, 11/24, 11/34, 11/44, 11/45, 11/70 or 11/94
    • This also sets up 18- or 22-bit memory management, special instructions, EIS and FPU
  • The model specific instructions and the most important differences between the system models are implemented to the point that many of the original MAINDEC test programs run without error
  • PDP2011 can drive a PDP-11 console
  • There are disk controllers for RK, RL and RM/RP disks; these use SD cards to store the disk image on
  • The system can be hooked up to a network; it includes a DEUNA compatible Ethernet frontend that works with the ENC424J600 Ethernet chip
    • You can run DECNET on RSTS and RSX, or TCP/IP on 2.11BSD
  • The PDP2011 project includes a terminal core to interface to a VGA screen and PS2 keyboard; you can combine it on the same FPGA you run the PDP-11 system, or run it on separate board
    • You can configure the terminal to be a vt100 or a vt105
  • Up to four serial ports can be configured for the console, additional terminals, links to other systems etc

PDP2011 FPGA Builds

The following model codes will produce working systems:

20; 11/20 system, no MMU, no FPU
34; 11/34 system, 18-bit MMU (2-bit ACF),FPU
44; 11/44 system, 22-bit MMU (2-bit ACF),FPU,Unibus map
45; 11/45 system, 18-bit MMU (3-bit ACF),FPU
70; 11/70 system, 22-bit MMU (3-bit ACF),FPU,Unibus map
94; 11/94 system, 22-bit MMU (2-bit ACF),FPU,Unibus map
  • My PDP-11 Builds
    • PDP-11/45
    • PDP-11/70

PDP-11/45

PDP-11/70

Hardware

QMTECH 5CEFA2F23 Datasheet CCA Pic.PNG

P1473-720px.jpg

  • FPGA card mounted on base board

RETROEP4CE15 REV4 P376-annotated-720px.jpg

PDP-11 FrontPanel P512-cropped-720px.jpg

Disks (SD card images) that work with PDP2011 build

PDP-11/45 Disks

DOS/BATCH-11 (rk05)

RT-11 4.0 (rk05)

RT-11FB 4.0 (rk05)

  • Switch settings
    • RK = Slide Switch 2 (in box)
    • Other Slide Switches off
  • RT-11FB (Foreground/Background) supported two tasks: a high-priority, non-interactive "Foreground" job, and a low-priority, interactive "Background" job
  • RT-11FB 4.0 (rk05)

RT-11 5.4 (rk05)

               RT-11 V5.4F

Installation of RT-11 Version 5.4F is complete and you are now running
RT-11 from your system volume,

Your system volume is your working volume if you have used the
automatic installation (AI) procedure. If you have installed RT-11 using
that procedure. DIGITAL recommends you verify the correct operation of 
your system's software using the VERIFY verification procedure.  
To do this, enter the command:

                             IND VERIFY

Note that VERIFY should be performed  only after the distribution 
media have been backed up.  This was accomplished as part
of automatic installation on  all  RL02,  RX02,  TK50, and  RX50
based systems,   including the  MicroPDP-11 and the Professional
300.  If you have not completed automatic installation, you must
perform a manual backup before using VERIFY.  Note also,  VERIFY
is NOT supported on RX01 diskettes,    DECtape I or II,   or the
Professional 325.

DIGITAL also  recommends  you  read  the  file V5NOTE.TXT, which
contains information  formalized too late to be included  in the
Release Notes.  V5NOTE.TXT can be TYPED or PRINTED.
  • Prompt is dot (.)
  • datime format
    • 01-May-99
  • type command
    • The type command will show the contents of a file, just like MS-DOS
  • RUN command
    • Dungeon for example is executed with RUN. I think you have to run .sav files.
    • .RUN DUNGEO
  • .SAV files can be run
    • .RUN DUNGEO
  • @ command
    • COM files are like batch scripts, and are executed with the @ infront of them.
    • .@STARTS.COM
  • SHOW command
    • This is a very useful command to show some info about the OS.
    • .SHOW

UNIX V7 (rl02)

  • Switch settings
    • RL = Slide Switch 1 (in box)
    • Other Slide Switches off
  • UNIX V7 (rl02) Disk Image
    • Write to SD card - used Balena Etcher (windows) to write SD card
  • Prompt is '@'
  • Type
boot
  • System responds with
New Boot, known devices are hp ht rk rl rp tm vt
  • Enter
rl(0,0)rl2unix
  • System responds with
mem = 177856
  • Ctrl-D to open shell
  • login: 'root'
  • Password: 'root'
  • There is no halt or shutdown command, the proper way to shutdown is to do a few sync
    • 'sync'
    • 'sync'
    • 'sync'
  • and just terminate the server session with a
    • .qq (???)

PDP-11/70 disks

211BSD (rp06)

  • Switch settings
    • RP = Slide Switch 3 (in box)
  • 211BSD (rp06) Disk Image
    • Write to SD card - used Balena Etcher (windows) to write SD card
  • Boot screen
Hello, world [t44]: cpu 11/70
boot from rp:
70Boot from xp(0,0,0) at 0176700
: «
: xp(0,0,0)unix
Boot: bootdev=05000 bootcsr=0176700
2.11 BSD UNIX #115: Sat Apr 22 19:07:25 PDT 2000
    sms1@curly.2bsd.com:/usr/src/sys/GENERIC
phys mem  = 3932160
avail mem = 3708224
user mem  = 307200
  • Running
  • Enter
  • At the first '#' prompt the system is in single-user mode. Just enter a ^D to continue the system startup to multi-user mode
  • Login: root
  • At the end is important to shutdown properly with a halt:
     # {pstat -T}
      49/186 files
      65/208 inodes
      16/150 processes
      11/ 46 texts active,  37 used
       3/135 swapmap entries,  530 kB used, 3649 kB free, 3642 kB max
      33/150 coremap entries, 2599 kB free, 2520 kB max
       1/ 10  ub_map entries,    8    free,    8    max
     # {mount}
     /dev/xp0a on /
     /dev/xp0c on /tmp
     /dev/xp0d on /home
     /dev/xp0e on /usr
     # {halt}
     syncing disks... done
     halting

RSX-11M PLUS 3.0 (rp06)

Other Disk Images

Other PDP2011 Builds

Software

Documentation

PDP-11 Front Panel

Front Panel Pins Directly Mapped to RETRO-EP4CE15

PDP-11 FrontPanel P512-cropped-720px.jpg

Front Panel J1

  • Front Panel Card cables up to 50-pin connector on RETRO-EP4CE15 Card
    • 32-pin connector
    • Wiring "flipped" and directly in order
    • Note extra ground/power pins on the Front Panel card

I/O Connector (5CEFA2F23 FPGA Card pin numbers)

Function Marking 5CEFA2 FPGA Pin
resetbtn pushbutton PB8 PIN_M22
PWR LED D8 PIN_L22
sdHC LED D7 PIN_M18
FETch LED D6 PIN_M20
sdWR LED D5 PIN_P16
sdRD LED D4 PIN_T19
RH Drive (rp) LED D3 PIN_R22
RK Drive LED D2 PIN_U20
RL Drive LED D1 PIN_U22
K11 (tty1) Slide switch SS4 PIN_P22
RH Drive (rp) (UP) Slide switch SS3 PIN_T22
RK Drive (UP) Slide switch SS2 PIN_V20
RL Drive (UP) Slide switch SS1 PIN_V21

LEDS-SWITCHES-2 P1 FPGA Pinout.PNG

P4 - SD Card (5CEFA2F23 FPGA pin numbers)

  • This build works with SD and SD/HC cards

RETROEP4CE15-P4 SD Card.PNG

  • SDCS = U7-57 = PIN_B15
  • MOSI = U7-58 = PIN_C15
  • SCK = U7-59 = PIN_C16
  • MISO = U7-60 = PIN_B16
  • SD_DETECT - PIN_B12

MultiComp in Box Pins Mapping

Slide Switches/Reset Pushbutton

  • Slide switches are on the bottom of the box

MultiCompInBox P1992 cropped 720px.jpg

RETROEP4-CE15 J3.PNG

  • Slide switches are on the bottom of the box
    • PIN_L17 - Slide Switch 1 (top switch) - RL Drive select
    • PIN_K17 - Slide Switch 2 - RK Drive select
    • PIN_K22 - Slide Switch 3 - RH/RP Drive select
    • PIN_K21 - Slide Switch 4 (bottom switch)
  • Reset switch is on the front of the boz
    • PIN_N16 - Reset Switch

SD Card

J1 PIN SIGNAL COLOR SD PIN FPGA Pin DIR
2 3.3V ORG 7 VREG 3.3V OUT (PWR)
45 sdSCLK GRY 3 PIN_L19 OUT
46 sdMISO BLU 2 PIN_L18 IN
47 sdMOSI WHT 4 PIN_L22 OUT
48 sdCS VIO 5 PIN_M22 OUT
49 GND GRN 1 GND OUT (PWR)

MultiComp DB-25 Pinout

  • MultiComp in a Box has a DB-25 Female connector
  • DB25-02 - DB-25 adapter with Male connector
  • Front panel card has 32-pin connector
  • Dupont pin cable connects the two cards
  • DB-25F on MultiComp in a Box as viewed from front of box

DB25F PINS.gif

Front Panel Pinout

LEDS-SWITCHES-2 P1 Pinout.PNG

MultiComp in Box Front Panel Cabling

DB25F P1(DB25-02) FPGA J1 Signal SW-J1 FPGA DB25F P1(DB25-02) FPGA J1 Signal SW-J1 FPGA
1 25 26 NC
2 23 GND 32 14 24 GND
3 21 44 SS1 5 PIN_M18 15 22 43 SS2 8 PIN_N19
4 19 42 SS3 11 PIN_M21 16 20 41 SS4 14 PIN_M20
5 17 40 N/C PIN_N20 17 18 39 N/C PIN_N21
6 15 38 LED1 6 PIN_P16 18 16 37 LED2 9 PIN_P17
7 13 36 LED3 12 PIN_T20 19 14 35 LED4 15 PIN_T19
8 11 34 LED5 18 PIN_P22 20 12 33 LED6 21 PIN_R21
9 9 32 LED7 24 PIN_R22 21 10 31 LED8 27 PIN_T22
10 7 30 PB8 28 PIN_U21 22 8 29 PIN_U20
11 5 23 6
12 3 24 4
13 1 +3.3V 2 25 2 +3.3V

Connectors on RETROEP4-CE15 Card

P1 - VGA

  • videoR0 = U8-49 = PIN_E12
  • videoR1 = U8-50 = PIN_D12
  • videoG0 = U8-51 = PIN_D13
  • videoG1 = U8-52 = PIN_C13
  • videoB0 = U8-53 = PIN_B13
  • videoB1 = U8-54 = PIN_A13
  • hSync = U8-55 = PIN_A15
  • vSync = U8-56 = PIN_A14

P2 - PS/2 Keyboard

PS2 Mapping.PNG

  • PS2DAT = U7-8 = PIN_BANK_2A_AA1
  • PS2CLK = U7-8 = PIN_NANK_2A_AA2

P3 - Serial Ports - I/O connector

  • fpgaRx1 (in) = PIN_C11
  • fpgaTx1 (out) = PIN_G10
  • fpgaRts1 = U7-44 = PIN_F10
  • fpgaCts1 = U7-46 = PIN_B11

IO conn

  • Second serial port on I/O connector
  • rx2 (in) = PIN_M18
  • tx2 (out) = PIN_L19
  • rts2 (out) = PIN_N19
  • cts2 (in) = PIN_M21

J4 - USB-B B (5CEFA2F23 FPGA Card pin numbers) Serial Port

  • On-board FT230X FTDI USB to Serial

RETROEP4CE15-Serial.PNG

FPGA Resources

  • Uses > 80% of the ALMs in Cyclone V 5CEFA2F23I7 part

PDP-11/45

+-------------------------------------------------------------------------------+
; Fitter Summary                                                                ;
+---------------------------------+---------------------------------------------+
; Fitter Status                   ; Successful - Sun May  1 13:02:25 2022       ;
; Quartus Prime Version           ; 21.1.0 Build 842 10/21/2021 SJ Lite Edition ;
; Revision Name                   ; top                                         ;
; Top-level Entity Name           ; top                                         ;
; Family                          ; Cyclone V                                   ;
; Device                          ; 5CEFA2F23I7                                 ;
; Timing Models                   ; Final                                       ;
; Logic utilization (in ALMs)     ; 7,797 / 9,430 ( 83 % )                      ;
; Total registers                 ; 6002                                        ;
; Total pins                      ; 68 / 224 ( 30 % )                           ;
; Total virtual pins              ; 0                                           ;
; Total block memory bits         ; 180,224 / 1,802,240 ( 10 % )                ;
; Total RAM Blocks                ; 25 / 176 ( 14 % )                           ;
; Total DSP Blocks                ; 1 / 25 ( 4 % )                              ;
; Total HSSI RX PCSs              ; 0                                           ;
; Total HSSI PMA RX Deserializers ; 0                                           ;
; Total HSSI TX PCSs              ; 0                                           ;
; Total HSSI PMA TX Serializers   ; 0                                           ;
; Total PLLs                      ; 1 / 4 ( 25 % )                              ;
; Total DLLs                      ; 0 / 4 ( 0 % )                               ;
+---------------------------------+---------------------------------------------+

PDP-11/70

+-------------------------------------------------------------------------------+
; Fitter Summary                                                                ;
+---------------------------------+---------------------------------------------+
; Fitter Status                   ; Successful - Sat Apr 30 19:30:51 2022       ;
; Quartus Prime Version           ; 21.1.0 Build 842 10/21/2021 SJ Lite Edition ;
; Revision Name                   ; top                                         ;
; Top-level Entity Name           ; top                                         ;
; Family                          ; Cyclone V                                   ;
; Device                          ; 5CEFA2F23I7                                 ;
; Timing Models                   ; Final                                       ;
; Logic utilization (in ALMs)     ; 7,809 / 9,430 ( 83 % )                      ;
; Total registers                 ; 6016                                        ;
; Total pins                      ; 76 / 224 ( 34 % )                           ;
; Total virtual pins              ; 0                                           ;
; Total block memory bits         ; 180,224 / 1,802,240 ( 10 % )                ;
; Total RAM Blocks                ; 25 / 176 ( 14 % )                           ;
; Total DSP Blocks                ; 1 / 25 ( 4 % )                              ;
; Total HSSI RX PCSs              ; 0                                           ;
; Total HSSI PMA RX Deserializers ; 0                                           ;
; Total HSSI TX PCSs              ; 0                                           ;
; Total HSSI PMA TX Serializers   ; 0                                           ;
; Total PLLs                      ; 1 / 4 ( 25 % )                              ;
; Total DLLs                      ; 0 / 4 ( 0 % )                               ;
+---------------------------------+---------------------------------------------+

External Resources

Programming the FPGA EEPROM (5CEFA2F23 FPGA)

  • File
  • Convert Programming File
  • Configuration Device = MT25QL128
  • Mode = Active Serial
  • Programming File Type: *.jic
  • Advanced = Check both Disables...
  • Select Flash Loader
  • Add Device = Cyclone V and 5CEFA2
  • Select SOF Data
  • Select Add File and select the .sof file
  • Generate
  • In Tools, Programmer
  • Mode: JTAG
  • Add file and select the .jic file
  • Select Program/Configure
  • Takes a while to program
  • Press button near VGA

Pin Lists

Pin List Standalone with Front Panel

To Direction Location I/O Standard Pull-Up
clkin Input PIN_M9 3.3-V LVTTL
cts1 Input PIN_B11 3.3-V LVTTL
dram_addr[0] Output PIN_P8 3.3-V LVTTL
dram_addr[1] Output PIN_P7 3.3-V LVTTL
dram_addr[10] Output PIN_R6 3.3-V LVTTL
dram_addr[11] Output PIN_T9 3.3-V LVTTL
dram_addr[12] Output PIN_Y9 3.3-V LVTTL
dram_addr[2] Output PIN_N8 3.3-V LVTTL
dram_addr[3] Output PIN_N6 3.3-V LVTTL
dram_addr[4] Output PIN_U6 3.3-V LVTTL
dram_addr[5] Output PIN_U7 3.3-V LVTTL
dram_addr[6] Output PIN_V6 3.3-V LVTTL
dram_addr[7] Output PIN_U8 3.3-V LVTTL
dram_addr[8] Output PIN_T8 3.3-V LVTTL
dram_addr[9] Output PIN_W8 3.3-V LVTTL
dram_ba_0 Output PIN_T7 3.3-V LVTTL
dram_ba_1 Output PIN_P9 3.3-V LVTTL
dram_cas_n Output PIN_AA7 3.3-V LVTTL
dram_cke Output PIN_V9 3.3-V LVTTL
dram_clk Output PIN_AB11 3.3-V LVTTL
dram_cs_n Output PIN_AB5 3.3-V LVTTL
dram_dq[0] Bidir PIN_AA12 3.3-V LVTTL
dram_dq[1] Bidir PIN_Y11 3.3-V LVTTL
dram_dq[10] Bidir PIN_U11 3.3-V LVTTL
dram_dq[11] Bidir PIN_R10 3.3-V LVTTL
dram_dq[12] Bidir PIN_R11 3.3-V LVTTL
dram_dq[13] Bidir PIN_U12 3.3-V LVTTL
dram_dq[14] Bidir PIN_R12 3.3-V LVTTL
dram_dq[15] Bidir PIN_P12 3.3-V LVTTL
dram_dq[2] Bidir PIN_AA10 3.3-V LVTTL
dram_dq[3] Bidir PIN_AB10 3.3-V LVTTL
dram_dq[4] Bidir PIN_Y10 3.3-V LVTTL
dram_dq[5] Bidir PIN_AA9 3.3-V LVTTL
dram_dq[6] Bidir PIN_AB8 3.3-V LVTTL
dram_dq[7] Bidir PIN_AA8 3.3-V LVTTL
dram_dq[8] Bidir PIN_U10 3.3-V LVTTL
dram_dq[9] Bidir PIN_T10 3.3-V LVTTL
dram_ldqm Output PIN_AB7 3.3-V LVTTL
dram_ras_n Output PIN_AB6 3.3-V LVTTL
dram_udqm Output PIN_V10 3.3-V LVTTL
dram_we_n Output PIN_W9 3.3-V LVTTL
i_PB[1] Input PIN_W19 3.3-V LVTTL
i_PB[2] Input PIN_U21 3.3-V LVTTL
i_PB[3] Input PIN_R21 3.3-V LVTTL
i_PB[4] Input PIN_T20 3.3-V LVTTL
i_PB[5] Input PIN_N21 3.3-V LVTTL
i_PB[6] Input PIN_M21 3.3-V LVTTL
i_PB[7] Input PIN_L19 3.3-V LVTTL
i_PB[8] Input PIN_M22 3.3-V LVTTL
i_SS[1] Input PIN_V21 3.3-V LVTTL
i_SS[2] Input PIN_V20 3.3-V LVTTL
i_SS[3] Input PIN_T22 3.3-V LVTTL
i_SS[4] Input PIN_P22 3.3-V LVTTL
i_SS[5] Input PIN_P17 3.3-V LVTTL
i_SS[6] Input PIN_N20 3.3-V LVTTL
i_SS[7] Input PIN_N19 3.3-V LVTTL
i_SS[8] Input PIN_L18 3.3-V LVTTL
o_LED[1] Output PIN_U22 3.3-V LVTTL
o_LED[2] Output PIN_U20 3.3-V LVTTL
o_LED[3] Output PIN_R22 3.3-V LVTTL
o_LED[4] Output PIN_T19 3.3-V LVTTL
o_LED[5] Output PIN_P16 3.3-V LVTTL
o_LED[6] Output PIN_M20 3.3-V LVTTL
o_LED[7] Output PIN_M18 3.3-V LVTTL
o_LED[8] Output PIN_L22 3.3-V LVTTL
ps2k_c Input PIN_AA2 3.3-V LVTTL
ps2k_d Input PIN_AA1 3.3-V LVTTL
rts1 Output PIN_F10 3.3-V LVTTL
rx1 Input PIN_C11 3.3-V LVTTL
sdcard_cs Output PIN_B15 3.3-V LVTTL
sdcard_miso Input PIN_B16 3.3-V LVTTL
sdcard_mosi Output PIN_C15 3.3-V LVTTL
sdcard_sclk Output PIN_C16 3.3-V LVTTL
tx1 Output PIN_G10 3.3-V LVTTL
vgab[0] Output PIN_B13 3.3-V LVTTL
vgab[1] Output PIN_A13 3.3-V LVTTL
vgag[0] Output PIN_D13 3.3-V LVTTL
vgag[1] Output PIN_C13 3.3-V LVTTL
vgah Output PIN_A15 3.3-V LVTTL
vgar[0] Output PIN_E12 3.3-V LVTTL
vgar[1] Output PIN_D12 3.3-V LVTTL
vgav Output PIN_A14 3.3-V LVTTL
xu_cs Output 3.3-V LVTTL
xu_debug_tx Output 3.3-V LVTTL
xu_miso Input 3.3-V LVTTL
xu_mosi Output 3.3-V LVTTL
xu_sclk Output 3.3-V LVTTL

qsf Standalone file with Front Panel

set_global_assignment -name FAMILY "Cyclone V"
set_global_assignment -name DEVICE 5CEFA2F23I7
set_global_assignment -name TOP_LEVEL_ENTITY top
set_global_assignment -name ORIGINAL_QUARTUS_VERSION 9.0
set_global_assignment -name PROJECT_CREATION_TIME_DATE "23:14:32  MARCH 19, 2009"
set_global_assignment -name LAST_QUARTUS_VERSION "21.1.0 Lite Edition"
set_global_assignment -name STRATIX_DEVICE_IO_STANDARD "3.3-V LVTTL"
set_global_assignment -name CYCLONEII_RESERVE_NCEO_AFTER_CONFIGURATION "USE AS REGULAR IO"
set_global_assignment -name RESERVE_ASDO_AFTER_CONFIGURATION "AS INPUT TRI-STATED"
set_global_assignment -name MIN_CORE_JUNCTION_TEMP "-40"
set_global_assignment -name MAX_CORE_JUNCTION_TEMP 100
set_global_assignment -name POWER_PRESET_COOLING_SOLUTION "23 MM HEAT SINK WITH 200 LFPM AIRFLOW"
set_global_assignment -name POWER_BOARD_THERMAL_MODEL "NONE (CONSERVATIVE)"
# Clock
set_location_assignment PIN_M9 -to clkin
# Pushbuttons on LEDS-SWITCHES-2 card
set_location_assignment PIN_M22 -to i_PB[8]
set_location_assignment PIN_L19 -to i_PB[7]
set_location_assignment PIN_M21 -to i_PB[6]
set_location_assignment PIN_N21 -to i_PB[5]
set_location_assignment PIN_T20 -to i_PB[4]
set_location_assignment PIN_R21 -to i_PB[3]
set_location_assignment PIN_U21 -to i_PB[2]
set_location_assignment PIN_W19 -to i_PB[1]
set_location_assignment PIN_L18 -to i_SS[8]
set_location_assignment PIN_N19 -to i_SS[7]
set_location_assignment PIN_N20 -to i_SS[6]
set_location_assignment PIN_P17 -to i_SS[5]
set_location_assignment PIN_P22 -to i_SS[4]
set_location_assignment PIN_T22 -to i_SS[3]
set_location_assignment PIN_V20 -to i_SS[2]
set_location_assignment PIN_V21 -to i_SS[1]
# LEDs on LEDS-SWITCHES-2 card
set_location_assignment PIN_L22 -to o_LED[8]
set_location_assignment PIN_M18 -to o_LED[7]
set_location_assignment PIN_M20 -to o_LED[6]
set_location_assignment PIN_P16 -to o_LED[5]
set_location_assignment PIN_T19 -to o_LED[4]
set_location_assignment PIN_R22 -to o_LED[3]
set_location_assignment PIN_U20 -to o_LED[2]
set_location_assignment PIN_U22 -to o_LED[1]
# SDRAM
set_location_assignment PIN_Y9 -to dram_addr[12]
set_location_assignment PIN_T9 -to dram_addr[11]
set_location_assignment PIN_R6 -to dram_addr[10]
set_location_assignment PIN_W8 -to dram_addr[9]
set_location_assignment PIN_T8 -to dram_addr[8]
set_location_assignment PIN_U8 -to dram_addr[7]
set_location_assignment PIN_V6 -to dram_addr[6]
set_location_assignment PIN_U7 -to dram_addr[5]
set_location_assignment PIN_U6 -to dram_addr[4]
set_location_assignment PIN_N6 -to dram_addr[3]
set_location_assignment PIN_N8 -to dram_addr[2]
set_location_assignment PIN_P7 -to dram_addr[1]
set_location_assignment PIN_P8 -to dram_addr[0]
set_location_assignment PIN_P9 -to dram_ba_1
set_location_assignment PIN_T7 -to dram_ba_0
set_location_assignment PIN_AA7 -to dram_cas_n
set_location_assignment PIN_V9 -to dram_cke
set_location_assignment PIN_AB11 -to dram_clk
set_location_assignment PIN_AB5 -to dram_cs_n
set_location_assignment PIN_P12 -to dram_dq[15]
set_location_assignment PIN_R12 -to dram_dq[14]
set_location_assignment PIN_U12 -to dram_dq[13]
set_location_assignment PIN_R11 -to dram_dq[12]
set_location_assignment PIN_R10 -to dram_dq[11]
set_location_assignment PIN_U11 -to dram_dq[10]
set_location_assignment PIN_T10 -to dram_dq[9]
set_location_assignment PIN_U10 -to dram_dq[8]
set_location_assignment PIN_AA8 -to dram_dq[7]
set_location_assignment PIN_AB8 -to dram_dq[6]
set_location_assignment PIN_AA9 -to dram_dq[5]
set_location_assignment PIN_Y10 -to dram_dq[4]
set_location_assignment PIN_AB10 -to dram_dq[3]
set_location_assignment PIN_AA10 -to dram_dq[2]
set_location_assignment PIN_Y11 -to dram_dq[1]
set_location_assignment PIN_AA12 -to dram_dq[0]
set_location_assignment PIN_V10 -to dram_udqm
set_location_assignment PIN_AB7 -to dram_ldqm
set_location_assignment PIN_AB6 -to dram_ras_n
set_location_assignment PIN_W9 -to dram_we_n
# Serial port (USB-to-Serial)
set_location_assignment PIN_C11 -to rx1
set_location_assignment PIN_G10 -to tx1
set_location_assignment PIN_F10 -to rts1
set_location_assignment PIN_B11 -to cts1
# Second serial port
# SD Card
set_location_assignment PIN_C16 -to sdcard_sclk
set_location_assignment PIN_B15 -to sdcard_cs
set_location_assignment PIN_B16 -to sdcard_miso
set_location_assignment PIN_C15 -to sdcard_mosi
# Ethernet
# PS/2 Keyboard
set_location_assignment PIN_AA2 -to ps2k_c
set_location_assignment PIN_AA1 -to ps2k_d
# Video
set_location_assignment PIN_E12 -to vgar[0]
set_location_assignment PIN_D12 -to vgar[1]
set_location_assignment PIN_B13 -to vgab[0]
set_location_assignment PIN_A13 -to vgab[1]
set_location_assignment PIN_D13 -to vgag[0]
set_location_assignment PIN_C13 -to vgag[1]
set_location_assignment PIN_A15 -to vgah
set_location_assignment PIN_A14 -to vgav

Pin List Standalone

qsf file Standalone

set_global_assignment -name FAMILY "Cyclone V"
set_global_assignment -name DEVICE 5CEFA2F23I7
set_global_assignment -name TOP_LEVEL_ENTITY top
set_global_assignment -name ORIGINAL_QUARTUS_VERSION 9.0
set_global_assignment -name PROJECT_CREATION_TIME_DATE "23:14:32  MARCH 19, 2009"
set_global_assignment -name LAST_QUARTUS_VERSION "21.1.0 Lite Edition"
set_global_assignment -name STRATIX_DEVICE_IO_STANDARD "3.3-V LVTTL"
set_global_assignment -name CYCLONEII_RESERVE_NCEO_AFTER_CONFIGURATION "USE AS REGULAR IO"
set_global_assignment -name RESERVE_ASDO_AFTER_CONFIGURATION "AS INPUT TRI-STATED"
set_location_assignment PIN_M9 -to clkin
set_location_assignment PIN_M22 -to resetbtn
set_instance_assignment -name WEAK_PULL_UP_RESISTOR ON -to resetbtn
# Control switches
# Jumpers on front edge
# SDRAM
set_location_assignment PIN_Y9 -to dram_addr[12]
set_location_assignment PIN_T9 -to dram_addr[11]
set_location_assignment PIN_R6 -to dram_addr[10]
set_location_assignment PIN_W8 -to dram_addr[9]
set_location_assignment PIN_T8 -to dram_addr[8]
set_location_assignment PIN_U8 -to dram_addr[7]
set_location_assignment PIN_V6 -to dram_addr[6]
set_location_assignment PIN_U7 -to dram_addr[5]
set_location_assignment PIN_U6 -to dram_addr[4]
set_location_assignment PIN_N6 -to dram_addr[3]
set_location_assignment PIN_N8 -to dram_addr[2]
set_location_assignment PIN_P7 -to dram_addr[1]
set_location_assignment PIN_P8 -to dram_addr[0]
set_location_assignment PIN_P9 -to dram_ba_1
set_location_assignment PIN_T7 -to dram_ba_0
set_location_assignment PIN_AA7 -to dram_cas_n
set_location_assignment PIN_V9 -to dram_cke
set_location_assignment PIN_AB11 -to dram_clk
set_location_assignment PIN_AB5 -to dram_cs_n
set_location_assignment PIN_P12 -to dram_dq[15]
set_location_assignment PIN_R12 -to dram_dq[14]
set_location_assignment PIN_U12 -to dram_dq[13]
set_location_assignment PIN_R11 -to dram_dq[12]
set_location_assignment PIN_R10 -to dram_dq[11]
set_location_assignment PIN_U11 -to dram_dq[10]
set_location_assignment PIN_T10 -to dram_dq[9]
set_location_assignment PIN_U10 -to dram_dq[8]
set_location_assignment PIN_AA8 -to dram_dq[7]
set_location_assignment PIN_AB8 -to dram_dq[6]
set_location_assignment PIN_AA9 -to dram_dq[5]
set_location_assignment PIN_Y10 -to dram_dq[4]
set_location_assignment PIN_AB10 -to dram_dq[3]
set_location_assignment PIN_AA10 -to dram_dq[2]
set_location_assignment PIN_Y11 -to dram_dq[1]
set_location_assignment PIN_AA12 -to dram_dq[0]
set_location_assignment PIN_V10 -to dram_udqm
set_location_assignment PIN_AB7 -to dram_ldqm
set_location_assignment PIN_AB6 -to dram_ras_n
set_location_assignment PIN_W9 -to dram_we_n
# Serial port (USB-to-Serial)
set_location_assignment PIN_L19 -to rx1
set_location_assignment PIN_L18 -to tx1
set_location_assignment PIN_M18 -to rts1
set_location_assignment PIN_N19 -to cts1
# Second serial port
# SD Card
set_location_assignment PIN_C16 -to sdcard_sclk
set_location_assignment PIN_B15 -to sdcard_cs
set_location_assignment PIN_B16 -to sdcard_miso
set_location_assignment PIN_C15 -to sdcard_mosi
# Seven segment display (on J1)
# Ethernet
set_location_assignment PIN_T20 -to xu_cs
set_location_assignment PIN_P17 -to xu_debug_tx
set_location_assignment PIN_P16 -to xu_miso
set_location_assignment PIN_N21 -to xu_mosi
set_location_assignment PIN_N20 -to xu_sclk
# PS/2 Keyboard
set_location_assignment PIN_AA2 -to ps2k_c
set_location_assignment PIN_AA1 -to ps2k_d
# Video
set_location_assignment PIN_A15 -to vgah
set_location_assignment PIN_A14 -to vgav

set_global_assignment -name PARTITION_NETLIST_TYPE SOURCE -section_id Top
set_global_assignment -name PARTITION_FITTER_PRESERVATION_LEVEL PLACEMENT_AND_ROUTING -section_id Top
set_global_assignment -name PARTITION_COLOR 16764057 -section_id Top

set_global_assignment -name MIN_CORE_JUNCTION_TEMP "-40"
set_global_assignment -name MAX_CORE_JUNCTION_TEMP 100
set_global_assignment -name POWER_PRESET_COOLING_SOLUTION "23 MM HEAT SINK WITH 200 LFPM AIRFLOW"
set_global_assignment -name POWER_BOARD_THERMAL_MODEL "NONE (CONSERVATIVE)"
set_location_assignment PIN_E12 -to vgar[0]
set_location_assignment PIN_D12 -to vgar[1]
set_location_assignment PIN_B13 -to vgab[0]
set_location_assignment PIN_A13 -to vgab[1]
set_location_assignment PIN_D13 -to vgag[0]
set_location_assignment PIN_C13 -to vgag[1]
set_location_assignment PIN_L17 -to sw[0]
set_location_assignment PIN_K17 -to sw[1]
set_location_assignment PIN_K22 -to sw[2]
set_location_assignment PIN_K21 -to sw[3]
set_location_assignment PIN_M16 -to sw[4]
set_location_assignment PIN_N16 -to sw[5]
set_location_assignment PIN_R21 -to greenled[0]
set_location_assignment PIN_P22 -to greenled[1]
set_location_assignment PIN_T22 -to greenled[2]
set_location_assignment PIN_R22 -to greenled[3]
set_location_assignment PIN_U20 -to greenled[4]
set_global_assignment -name VHDL_FILE ../vgacr.vhd
set_global_assignment -name VHDL_FILE ../vga.vhd
set_global_assignment -name VHDL_FILE ../vt.vhd
set_global_assignment -name VHDL_FILE ../ps2.vhd
set_global_assignment -name VHDL_FILE ../vgafont.vhd
set_global_assignment -name VHDL_FILE ../vtbrt42.vhd
set_global_assignment -name VHDL_FILE ../sdspi.vhd
set_global_assignment -name VHDL_FILE ../mnckw.vhd
set_global_assignment -name VHDL_FILE ../mncdo.vhd
set_global_assignment -name VHDL_FILE ../mncdi.vhd
set_global_assignment -name VHDL_FILE ../mncad.vhd
set_global_assignment -name VHDL_FILE ../mncaa.vhd
set_global_assignment -name VHDL_FILE ../m9312h47.vhd
set_global_assignment -name VHDL_FILE ../m9312l47.vhd
set_global_assignment -name VHDL_FILE ../dr11c.vhd
set_global_assignment -name VHDL_FILE ../panelos.vhd
set_global_assignment -name VHDL_FILE ../paneldriver.vhd
set_global_assignment -name VHDL_FILE ../paneldb.vhd
set_global_assignment -name VHDL_FILE ../xubrt45.vhd
set_global_assignment -name VHDL_FILE ../xubm.vhd
set_global_assignment -name VHDL_FILE ../xubl.vhd
set_global_assignment -name VHDL_FILE ../xu.vhd
set_global_assignment -name VHDL_FILE ../rh11.vhd
set_global_assignment -name VHDL_FILE ../kl11.vhd
set_global_assignment -name VHDL_FILE ../rk11.vhd
set_global_assignment -name VHDL_FILE ../unibus.vhd
set_global_assignment -name VHDL_FILE ../cr.vhd
set_global_assignment -name VHDL_FILE ../rl11.vhd
set_global_assignment -name VHDL_FILE ../mmu.vhd
set_global_assignment -name VHDL_FILE ../kw11l.vhd
set_global_assignment -name VHDL_FILE ../fpuregs.vhd
set_global_assignment -name VHDL_FILE ../csdr.vhd
set_global_assignment -name VHDL_FILE ../cpuregs.vhd
set_global_assignment -name VHDL_FILE ../cpu.vhd
set_global_assignment -name VHDL_FILE top.vhd
set_global_assignment -name VHDL_FILE ssegdecoder.vhd
set_global_assignment -name CDF_FILE top.cdf
set_global_assignment -name QIP_FILE pll.qip
set_instance_assignment -name PARTITION_HIERARCHY root_partition -to | -section_id Top

Pin List in MultiComp Box

To Direction Location Pull-Up
clkin Input PIN_M9
cts1 Input PIN_B11 on
dram_addr[12] Output PIN_Y9
dram_addr[11] Output PIN_T9
dram_addr[10] Output PIN_R6
dram_addr[9] Output PIN_W8
dram_addr[8] Output PIN_T8
dram_addr[7] Output PIN_U8
dram_addr[6] Output PIN_V6
dram_addr[5] Output PIN_U7
dram_addr[4] Output PIN_U6
dram_addr[3] Output PIN_N6
dram_addr[2] Output PIN_N8
dram_addr[1] Output PIN_P7
dram_addr[0] Output PIN_P8
dram_ba_0 Output PIN_T7
dram_ba_1 Output PIN_P9
dram_cas_n Output PIN_AA7
dram_cke Output PIN_V9
dram_clk Output PIN_AB11
dram_cs_n Output PIN_AB5
dram_dq[15] Bidir PIN_P12
dram_dq[14] Bidir PIN_R12
dram_dq[13] Bidir PIN_U12
dram_dq[12] Bidir PIN_R11
dram_dq[11] Bidir PIN_R10
dram_dq[10] Bidir PIN_U11
dram_dq[9] Bidir PIN_T10
dram_dq[8] Bidir PIN_U10
dram_dq[7] Bidir PIN_AA8
dram_dq[6] Bidir PIN_AB8
dram_dq[5] Bidir PIN_AA9
dram_dq[4] Bidir PIN_Y10
dram_dq[3] Bidir PIN_AB10
dram_dq[2] Bidir PIN_AA10
dram_dq[1] Bidir PIN_Y11
dram_dq[0] Bidir PIN_AA12
dram_ldqm Output PIN_AB7
dram_ras_n Output PIN_AB6
dram_udqm Output PIN_V10
dram_we_n Output PIN_W9
i_PB[8] Input PIN_N16 on
i_PB[7] Input PIN_Y20 on
i_PB[6] Input PIN_M21 on
i_PB[5] Input PIN_N21 on
i_PB[4] Input PIN_T20 on
i_PB[3] Input PIN_R21 on
i_PB[2] Input PIN_U21 on
i_PB[1] Input PIN_W19 on
i_SS[8] Input PIN_P22 on
i_SS[7] Input PIN_N19 on
i_SS[6] Input PIN_N20 on
i_SS[5] Input PIN_M16 on
i_SS[4] Input PIN_K21 on
i_SS[3] Input PIN_K22 on
i_SS[2] Input PIN_K17 on
i_SS[1] Input PIN_L17 on
o_LED[8] Output PIN_P17
o_LED[7] Output PIN_M18
o_LED[6] Output PIN_M20
o_LED[5] Output PIN_P16
o_LED[4] Output PIN_T19
o_LED[3] Output PIN_R22
o_LED[2] Output PIN_U20
o_LED[1] Output PIN_U22
ps2k_c Input PIN_AA2 on
ps2k_d Input PIN_AA1 on
rts1 Output PIN_F10
rx1 Input PIN_C11 on
sdcard_cs Output PIN_M22
sdcard_miso Input PIN_L18 on
sdcard_mosi Output PIN_L22
sdcard_sclk Output PIN_L19
tx1 Output PIN_G10
vgab[1] Output PIN_A13
vgab[0] Output PIN_B13
vgag[1] Output PIN_C13
vgag[0] Output PIN_D13
vgah Output PIN_A15
vgar[1] Output PIN_D12
vgar[0] Output PIN_E12
vgav Output PIN_A14
xu_cs Output PIN_AB22
xu_debug_tx Output PIN_AA22
xu_miso Input PIN_Y22 on
xu_mosi Output PIN_V20
xu_sclk Output PIN_T22

qsf file in MultiComp Box

set_global_assignment -name FAMILY "Cyclone V"
set_global_assignment -name DEVICE 5CEFA2F23I7
set_global_assignment -name TOP_LEVEL_ENTITY top
set_global_assignment -name ORIGINAL_QUARTUS_VERSION 9.0
set_global_assignment -name PROJECT_CREATION_TIME_DATE "23:14:32  MARCH 19, 2009"
set_global_assignment -name LAST_QUARTUS_VERSION "21.1.0 Lite Edition"
set_global_assignment -name STRATIX_DEVICE_IO_STANDARD "3.3-V LVTTL"
set_global_assignment -name CYCLONEII_RESERVE_NCEO_AFTER_CONFIGURATION "USE AS REGULAR IO"
set_global_assignment -name RESERVE_ASDO_AFTER_CONFIGURATION "AS INPUT TRI-STATED"
set_global_assignment -name PARTITION_NETLIST_TYPE SOURCE -section_id Top
set_global_assignment -name PARTITION_FITTER_PRESERVATION_LEVEL PLACEMENT_AND_ROUTING -section_id Top
set_global_assignment -name PARTITION_COLOR 16764057 -section_id Top
set_global_assignment -name MIN_CORE_JUNCTION_TEMP "-40"
set_global_assignment -name MAX_CORE_JUNCTION_TEMP 100
set_global_assignment -name POWER_PRESET_COOLING_SOLUTION "23 MM HEAT SINK WITH 200 LFPM AIRFLOW"
set_global_assignment -name POWER_BOARD_THERMAL_MODEL "NONE (CONSERVATIVE)"
# Clock
set_location_assignment PIN_M9 -to clkin
# Serial port (USB-to-Serial)
set_location_assignment PIN_C11 -to rx1
set_location_assignment PIN_G10 -to tx1
set_location_assignment PIN_F10 -to rts1
set_location_assignment PIN_B11 -to cts1
set_instance_assignment -name WEAK_PULL_UP_RESISTOR ON -to cts1
set_instance_assignment -name WEAK_PULL_UP_RESISTOR ON -to rx1
# Second serial port
# SD Card
set_location_assignment PIN_L19 -to sdcard_sclk
set_location_assignment PIN_M22 -to sdcard_cs
set_location_assignment PIN_L18 -to sdcard_miso
set_instance_assignment -name WEAK_PULL_UP_RESISTOR ON -to sdcard_miso
set_location_assignment PIN_L22 -to sdcard_mosi
# PS/2 Keyboard
set_location_assignment PIN_AA2 -to ps2k_c
set_location_assignment PIN_AA1 -to ps2k_d
set_instance_assignment -name WEAK_PULL_UP_RESISTOR ON -to ps2k_c
set_instance_assignment -name WEAK_PULL_UP_RESISTOR ON -to ps2k_d
# Video
set_location_assignment PIN_A15 -to vgah
set_location_assignment PIN_A14 -to vgav
set_location_assignment PIN_E12 -to vgar[0]
set_location_assignment PIN_D12 -to vgar[1]
set_location_assignment PIN_B13 -to vgab[0]
set_location_assignment PIN_A13 -to vgab[1]
set_location_assignment PIN_D13 -to vgag[0]
set_location_assignment PIN_C13 -to vgag[1]
# LEDs
set_location_assignment PIN_U22 -to o_LED[1]
set_location_assignment PIN_R22 -to o_LED[3]
set_location_assignment PIN_U20 -to o_LED[2]
set_location_assignment PIN_P17 -to o_LED[8]
set_location_assignment PIN_M18 -to o_LED[7]
set_location_assignment PIN_M20 -to o_LED[6]
set_location_assignment PIN_P16 -to o_LED[5]
set_location_assignment PIN_T19 -to o_LED[4]
# Slide Switches
set_location_assignment PIN_L17 -to i_SS[1]
set_location_assignment PIN_K17 -to i_SS[2]
set_location_assignment PIN_K22 -to i_SS[3]
set_location_assignment PIN_K21 -to i_SS[4]
set_location_assignment PIN_M16 -to i_SS[5]
set_location_assignment PIN_N20 -to i_SS[6]
set_location_assignment PIN_N19 -to i_SS[7]
set_location_assignment PIN_P22 -to i_SS[8]
set_instance_assignment -name WEAK_PULL_UP_RESISTOR ON -to i_SS[8]
set_instance_assignment -name WEAK_PULL_UP_RESISTOR ON -to i_SS[7]
set_instance_assignment -name WEAK_PULL_UP_RESISTOR ON -to i_SS[6]
set_instance_assignment -name WEAK_PULL_UP_RESISTOR ON -to i_SS[5]
set_instance_assignment -name WEAK_PULL_UP_RESISTOR ON -to i_SS[4]
set_instance_assignment -name WEAK_PULL_UP_RESISTOR ON -to i_SS[3]
set_instance_assignment -name WEAK_PULL_UP_RESISTOR ON -to i_SS[2]
set_instance_assignment -name WEAK_PULL_UP_RESISTOR ON -to i_SS[1]
set_instance_assignment -name WEAK_PULL_UP_RESISTOR ON -to i_SS
# Pushbuttons
set_location_assignment PIN_W19 -to i_PB[1]
set_location_assignment PIN_U21 -to i_PB[2]
set_location_assignment PIN_R21 -to i_PB[3]
set_location_assignment PIN_T20 -to i_PB[4]
set_location_assignment PIN_N21 -to i_PB[5]
set_location_assignment PIN_M21 -to i_PB[6]
set_location_assignment PIN_Y20 -to i_PB[7]
set_location_assignment PIN_N16 -to i_PB[8]
set_instance_assignment -name WEAK_PULL_UP_RESISTOR ON -to i_PB[1]
set_instance_assignment -name WEAK_PULL_UP_RESISTOR ON -to i_PB[2]
set_instance_assignment -name WEAK_PULL_UP_RESISTOR ON -to i_PB[3]
set_instance_assignment -name WEAK_PULL_UP_RESISTOR ON -to i_PB[4]
set_instance_assignment -name WEAK_PULL_UP_RESISTOR ON -to i_PB[5]
set_instance_assignment -name WEAK_PULL_UP_RESISTOR ON -to i_PB[6]
set_instance_assignment -name WEAK_PULL_UP_RESISTOR ON -to i_PB[7]
set_instance_assignment -name WEAK_PULL_UP_RESISTOR ON -to i_PB[8]
# Ethernet
set_location_assignment PIN_T22 -to xu_sclk
set_location_assignment PIN_V20 -to xu_mosi
set_location_assignment PIN_Y22 -to xu_miso
set_location_assignment PIN_AA22 -to xu_debug_tx
set_location_assignment PIN_AB22 -to xu_cs
set_instance_assignment -name WEAK_PULL_UP_RESISTOR ON -to xu_miso
# SDRAM
set_location_assignment PIN_Y9 -to dram_addr[12]
set_location_assignment PIN_T9 -to dram_addr[11]
set_location_assignment PIN_R6 -to dram_addr[10]
set_location_assignment PIN_W8 -to dram_addr[9]
set_location_assignment PIN_T8 -to dram_addr[8]
set_location_assignment PIN_U8 -to dram_addr[7]
set_location_assignment PIN_V6 -to dram_addr[6]
set_location_assignment PIN_U7 -to dram_addr[5]
set_location_assignment PIN_U6 -to dram_addr[4]
set_location_assignment PIN_N6 -to dram_addr[3]
set_location_assignment PIN_N8 -to dram_addr[2]
set_location_assignment PIN_P7 -to dram_addr[1]
set_location_assignment PIN_P8 -to dram_addr[0]
set_location_assignment PIN_P9 -to dram_ba_1
set_location_assignment PIN_T7 -to dram_ba_0
set_location_assignment PIN_AA7 -to dram_cas_n
set_location_assignment PIN_V9 -to dram_cke
set_location_assignment PIN_AB11 -to dram_clk
set_location_assignment PIN_AB5 -to dram_cs_n
set_location_assignment PIN_P12 -to dram_dq[15]
set_location_assignment PIN_R12 -to dram_dq[14]
set_location_assignment PIN_U12 -to dram_dq[13]
set_location_assignment PIN_R11 -to dram_dq[12]
set_location_assignment PIN_R10 -to dram_dq[11]
set_location_assignment PIN_U11 -to dram_dq[10]
set_location_assignment PIN_T10 -to dram_dq[9]
set_location_assignment PIN_U10 -to dram_dq[8]
set_location_assignment PIN_AA8 -to dram_dq[7]
set_location_assignment PIN_AB8 -to dram_dq[6]
set_location_assignment PIN_AA9 -to dram_dq[5]
set_location_assignment PIN_Y10 -to dram_dq[4]
set_location_assignment PIN_AB10 -to dram_dq[3]
set_location_assignment PIN_AA10 -to dram_dq[2]
set_location_assignment PIN_Y11 -to dram_dq[1]
set_location_assignment PIN_AA12 -to dram_dq[0]
set_location_assignment PIN_V10 -to dram_udqm
set_location_assignment PIN_AB7 -to dram_ldqm
set_location_assignment PIN_AB6 -to dram_ras_n
set_location_assignment PIN_W9 -to dram_we_n
# 
set_global_assignment -name VHDL_FILE ../vgacr.vhd
set_global_assignment -name VHDL_FILE ../vga.vhd
set_global_assignment -name VHDL_FILE ../vt.vhd
set_global_assignment -name VHDL_FILE ../ps2.vhd
set_global_assignment -name VHDL_FILE ../vgafont.vhd
set_global_assignment -name VHDL_FILE ../vtbrt42.vhd
set_global_assignment -name VHDL_FILE ../sdspi.vhd
set_global_assignment -name VHDL_FILE ../mnckw.vhd
set_global_assignment -name VHDL_FILE ../mncdo.vhd
set_global_assignment -name VHDL_FILE ../mncdi.vhd
set_global_assignment -name VHDL_FILE ../mncad.vhd
set_global_assignment -name VHDL_FILE ../mncaa.vhd
set_global_assignment -name VHDL_FILE ../m9312h47.vhd
set_global_assignment -name VHDL_FILE ../m9312l47.vhd
set_global_assignment -name VHDL_FILE ../dr11c.vhd
set_global_assignment -name VHDL_FILE ../panelos.vhd
set_global_assignment -name VHDL_FILE ../paneldriver.vhd
set_global_assignment -name VHDL_FILE ../paneldb.vhd
set_global_assignment -name VHDL_FILE ../xubrt45.vhd
set_global_assignment -name VHDL_FILE ../xubm.vhd
set_global_assignment -name VHDL_FILE ../xubl.vhd
set_global_assignment -name VHDL_FILE ../xu.vhd
set_global_assignment -name VHDL_FILE ../rh11.vhd
set_global_assignment -name VHDL_FILE ../kl11.vhd
set_global_assignment -name VHDL_FILE ../rk11.vhd
set_global_assignment -name VHDL_FILE ../unibus.vhd
set_global_assignment -name VHDL_FILE ../cr.vhd
set_global_assignment -name VHDL_FILE ../rl11.vhd
set_global_assignment -name VHDL_FILE ../mmu.vhd
set_global_assignment -name VHDL_FILE ../kw11l.vhd
set_global_assignment -name VHDL_FILE ../fpuregs.vhd
set_global_assignment -name VHDL_FILE ../csdr.vhd
set_global_assignment -name VHDL_FILE ../cpuregs.vhd
set_global_assignment -name VHDL_FILE ../cpu.vhd
set_global_assignment -name VHDL_FILE top.vhd
set_global_assignment -name VHDL_FILE ssegdecoder.vhd
set_global_assignment -name CDF_FILE top.cdf
set_global_assignment -name QIP_FILE pll.qip
set_instance_assignment -name PARTITION_HIERARCHY root_partition -to | -section_id Top