Difference between revisions of "SD CARD X49"
Jump to navigation
Jump to search
Blwikiadmin (talk | contribs) |
Blwikiadmin (talk | contribs) |
||
| (20 intermediate revisions by the same user not shown) | |||
| Line 26: | Line 26: | ||
== J1 pinout == | == J1 pinout == | ||
| + | |||
| + | [[FILE:SD_CARD_X49_J1.PNG]] | ||
# GND | # GND | ||
| Line 35: | Line 37: | ||
# 3.3V in/out | # 3.3V in/out | ||
# 5V in (for 5V host only) | # 5V in (for 5V host only) | ||
| + | |||
| + | == Schematic == | ||
| + | |||
| + | * [http://land-boards.com/SD_CARD_X49/SD_CARD_X49_REV1_SCHEMATIC.pdf Rev 1 Schematic] | ||
| + | * [http://land-boards.com/SD_CARD_X49/SD_CARD_X49_REV2_SCHEMATIC.pdf Rev 2 Schematic] | ||
== Lock/Unlock == | == Lock/Unlock == | ||
| Line 61: | Line 68: | ||
== Testing == | == Testing == | ||
| − | * [ | + | * Testing is done using an Arduino uno at 5V |
| + | |||
| + | [[FILE:SD_CARD_X49-TESTING-P18101-720px.jpg]] | ||
| + | |||
| + | === Hardware === | ||
| + | |||
| + | * Unit Under Test (UUT) | ||
| + | ** NO5V jumper not installed | ||
* Arduino UNO card | * Arduino UNO card | ||
| − | |||
* FAT32 card with files on it | * FAT32 card with files on it | ||
| − | * Cabling | + | * [[Arduino Sensor Shield]] |
| + | ** GVS connections | ||
| + | |||
| + | [[file:HCARDU0015_Diagram.png]] | ||
| + | |||
| + | ==== Test Cabling ==== | ||
| + | |||
| + | * USB cable to PC | ||
| + | * Cable from Arduino Sensor Shield to UUT | ||
** 2x3 Dupont to D13/D12 and D11/D10 | ** 2x3 Dupont to D13/D12 and D11/D10 | ||
** 8 pin Dupont to SD card | ** 8 pin Dupont to SD card | ||
| − | + | {| class="wikitable" | |
| − | + | ! Signal Name | |
| − | + | ! SD Card pin | |
| − | + | ! Color | |
| − | + | ! Sensor Shield pin | |
| − | + | |- | |
| − | + | | GND | |
| − | + | | 1 | |
| + | | Green | ||
| + | | D13 GND | ||
| + | |- | ||
| + | | MISO | ||
| + | | 2 | ||
| + | | Violet | ||
| + | | D12 | ||
| + | |- | ||
| + | | SCLK | ||
| + | | 3 | ||
| + | | Grey | ||
| + | | D13 | ||
| + | |- | ||
| + | | MOSI | ||
| + | | 4 | ||
| + | | Brown | ||
| + | | D11 | ||
| + | |- | ||
| + | | SPI_SS | ||
| + | | 5 | ||
| + | | Yellow | ||
| + | | D10 | ||
| + | |- | ||
| + | | CARD_DETECT (no pull-up) | ||
| + | | 6 | ||
| + | | None | ||
| + | | N/A | ||
| + | |- | ||
| + | | 3.3V in/out | ||
| + | | 7 | ||
| + | | None | ||
| + | | N/A | ||
| + | |- | ||
| + | | 5V in (for 5V host only) | ||
| + | | 8 | ||
| + | | Orange | ||
| + | | D13 VCC | ||
| + | |- | ||
| + | |} | ||
| + | |||
| + | === Debugging === | ||
| + | |||
| + | * Error message | ||
| + | <pre> | ||
| + | Initializing SD card...initialization failed. Things to check: | ||
| + | 1. is a card inserted? | ||
| + | 2. is your wiring correct? | ||
| + | 3. did you change the chipSelect pin to match your shield or module? | ||
| + | Note: press reset or reopen this serial monitor after fixing your issue! | ||
| + | </pre> | ||
| + | * If test fails verify SD card is good in SD card adapter on PC | ||
| + | |||
| + | === Software === | ||
| + | |||
| + | * [https://github.com/land-boards/lb-Arduino-Code/tree/master/LBCards/SDCard/SD_Dir Arduino Sketch used to test cards] | ||
| + | ** [https://www.arduino.cc/en/Tutorial/LibraryExamples/Listfiles Using the SD library to print the directory of files on SD card] - Arduino code | ||
| + | |||
| + | === Running === | ||
| + | * SD card with something on it | ||
* Run Serial Monitor | * Run Serial Monitor | ||
| − | ** | + | ** 9600 baud |
* Prints directory to monitor | * Prints directory to monitor | ||
| + | <pre> | ||
| + | Initializing SD card...initialization done. | ||
| + | SYSTEM~1/ | ||
| + | WPSETT~1.DAT 12 | ||
| + | INDEXE~1 76 | ||
| + | README.TXT 1372 | ||
| + | done! | ||
| + | </pre> | ||
| + | * Reset button on sensor shield to re-run | ||
== Mounting == | == Mounting == | ||
Latest revision as of 14:12, 31 March 2023
Contents
Features
- SD or SDHC card adapter
- 5V to 3.3V regulator
- 3.3V to 5V TXS0104E level shifter
- Activity LED
- 49 x 49 mm ODAS foprm factor
- (4) 4-40 mounting holes
Power Options
Important to properly set up the power option
- 3.3V Host
- Wire power to 3.3V position
- Install Jumper J3
- Leave 5V in pin open
- 5V Host
- Wire Power to 5V
- Leave 3.3V open
- Remove Jumper J3
J1 pinout
- GND
- MISO
- SCLK
- MOSI
- SPI_SS
- CARD_DETECT (no pull-up)
- 3.3V in/out
- 5V in (for 5V host only)
Schematic
Lock/Unlock
- Set switch to not locked position
Used with Z80_PSOC card
- PSOC Pins
- MISO - PSOC pin 76
- MOSI - PSOC pin 77
- SCLK - PSOC pin 78
- SPI_SS - PSOC pin 79
Z80_PSOC - H3 Connector
- GND
- +5V
- SPI_SS - PSOC pin 79
- SCLK - PSOC pin 78
- MOSI - PSOC pin 77
- MISO - PSOC pin 76
Testing
- Testing is done using an Arduino uno at 5V
Hardware
- Unit Under Test (UUT)
- NO5V jumper not installed
- Arduino UNO card
- FAT32 card with files on it
- Arduino Sensor Shield
- GVS connections
Test Cabling
- USB cable to PC
- Cable from Arduino Sensor Shield to UUT
- 2x3 Dupont to D13/D12 and D11/D10
- 8 pin Dupont to SD card
| Signal Name | SD Card pin | Color | Sensor Shield pin |
|---|---|---|---|
| GND | 1 | Green | D13 GND |
| MISO | 2 | Violet | D12 |
| SCLK | 3 | Grey | D13 |
| MOSI | 4 | Brown | D11 |
| SPI_SS | 5 | Yellow | D10 |
| CARD_DETECT (no pull-up) | 6 | None | N/A |
| 3.3V in/out | 7 | None | N/A |
| 5V in (for 5V host only) | 8 | Orange | D13 VCC |
Debugging
- Error message
Initializing SD card...initialization failed. Things to check: 1. is a card inserted? 2. is your wiring correct? 3. did you change the chipSelect pin to match your shield or module? Note: press reset or reopen this serial monitor after fixing your issue!
- If test fails verify SD card is good in SD card adapter on PC
Software
Running
- SD card with something on it
- Run Serial Monitor
- 9600 baud
- Prints directory to monitor
Initializing SD card...initialization done.
SYSTEM~1/
WPSETT~1.DAT 12
INDEXE~1 76
README.TXT 1372
done!
- Reset button on sensor shield to re-run
Mounting
Card Mounted in a Chassis
Mounted on ODAS Carrier Card
