Difference between revisions of "Land Boards Synth Components"

From Land Boards Wiki
Jump to navigation Jump to search
Line 150: Line 150:
  
 
[[FILE:DUAL_LINEAR_PS_SCHEM.PNG]]
 
[[FILE:DUAL_LINEAR_PS_SCHEM.PNG]]
 +
 +
=== Eurorack DIY Panel ===
  
 
== Reference Docs ==
 
== Reference Docs ==

Revision as of 09:24, 4 October 2022

Synth Modules

MIDI-IN-OUT

MIDI-IN-OUT REV1 FRONT 3D.png

  • MIDI-IN-OUT - MIDI In/Out
  • MIDI In/Out Jacks
  • 5V MIDI
  • 3.3V or 5V Serial connections
  • MIDI In is opto-isolated
  • (2) 4-40 Mounting holes

SCF-2

  • SCF-2 - Dual 3.5mm Audio Jacks (Scale, Clip, Filter)

SCF-2 REV 1 FRONT 3D.png

  • Digital Inputs or Outputs
  • (2) 3.5mm Jacks
  • Scaling resistors
  • Schottky Clamping Diodes
  • Filter cap
  • Ring pin brought to connector
    • Ring pin is not used in Synth applications
    • Card can be used as a 3.5mm breakout
  • (2) 4-40 mounting holes

SYNTH-VCO-01

SYNTH-VCO-01 REV1 FRONT 3D.png

  • Build of Pico VCO by HAGIWO
  • Digital Voltage Controlled Oscillator (VCO)
  • Three modes: Wavefold, FM and AM
  • PWM output with 2 pole low pass filter
  • Each mode has eight built-in waveforms
  • XIAO RP2040 CPU
  • (5) Pushbuttons
    • Octave Up/Down
    • Mode Up/Down (Wavefold, FM and AM)
    • Push Timbre switches between 8 waveforms
  • (2) Knobs
    • Freq fine adjust
    • Mod adjust
  • Standard EuroRack 16 pin header
    • Supports 12V in with on-board 5V regulator
    • 5V regulator can be not installed if 5V is available on EuroRack connection
  • Card is not a Eurorack card
    • Probably too deep, needs cabling
  • (4) 6-32 mounting holes

SYNTH-MIDI-CTL-01

SYNTH-MIDI CTL-01 REV1 FRONT 3D.png


  • Adapted from HAGIWO's MIDI to CV module
    • Translate from Japanese to English using browser
  • XAIO RP2040 CPU
    • Arduino MIDI library has not yet been ported to Pico so will need to use CircuitPython
  • MIDI In/Out
    • Standard MIDI Jacks
    • MIDI out jack for future functionality
  • (2) 0-5V Analog CV outs
  • (2) Digital Outs, eX:
    • Gate
    • Clock
  • Pot supports setting Clock rate
  • Standard EuroRack 16 pin header
    • Supports 12V in with on-board 5V regulator
    • 5V regulator can be not installed if 5V is available on EuroRack connection
  • Card is not a Eurorack card
    • Probably too deep, needs cabling
  • (6) 6-32 Mounting holes

SYNTH-MIDI-CV4-01

SYNTH-MIDI CV4-01 REV1 FRONT 3D.png

  • Adapted from HAGIWO's MIDI to CV module
    • Translate from Japanese to English using browser
    • Removes Digital Outputs
    • Has 4 Analog Outputs instead of 2
  • XAIO RP2040 CPU
    • Arduino MIDI library has not yet been ported to Pico so will need to use CircuitPython
  • MIDI In
    • Standard MIDI Jacks
    • MIDI out jack for future functionality
  • (4) 0-5V Analog CV outs
  • Standard EuroRack 16 pin header
    • Supports 12V in with on-board 5V regulator
    • 5V regulator can be not installed if 5V is available on EuroRack connection
  • Card is not a Eurorack card
    • Probably too deep, needs cabling
  • (6) 6-32 Mounting holes

6 Channel Mixer

SYNTH-MIXER6-01 SET FRONT 3D.png

RP2040 VCO

  • SYNTH-VCO-03
  • Eurorack 6HP
  • (3) Card set
  • Views: Control Panel rear side, Control Panel controls side, Logic card component side, Logic card rear side, Front Panel

SYNTH-VCO CTL-01-CARD SET-3D.png

Eurorack +/- 12V Power Supply

DUAL LINEAR PS SCHEM.PNG

Eurorack DIY Panel

Reference Docs

Projects

Module Kits

Software

Hardware/Parts

Samples

HAGIWO Builds

FUNCTION 3.5MM POTS TOGG PBS ROT DIN5 CPU LINK
MIDI-IN-OUT 0 0 0 0 0 2 NONE
SCF-2 2 0 0 0 0 0 NONE
SYNTH-MIDI-CTL-01 4 0 0 0 0 2 XAIO RP2040
SYNTH-MIDI-CV4-01 4 0 0 0 0 2 XAIO RP2040
SYNTH-MIXER6-01 7 7 0 0 0 0 NONE https://note.com/solder_state/n/nffc1a33053be
SYNTH-VCO-01 4 2 2 1 0 0 XAIO RP2040 https://note.com/solder_state/n/nca6a1dec3921
SYNTH-VCO-03 4 2 2 1 0 0 XAIO RP2040 https://note.com/solder_state/n/nca6a1dec3921
No.56 Sample Drum 3 1 1 0 0 0 ESP32C3 https://note.com/solder_state/n/n950ed088c3cb
No.55 V2164 Dual VCA 6 6 0 0 0 0 NONE https://note.com/solder_state/n/nd82c027d0597
No.54 PT2399 clock sync delay 4 3 1 0 0 0 NANO https://note.com/solder_state/n/nf6dc0a61e26d
No.52 Reverse step sequencer 4 8 2 0 0 0 CDT7350 https://note.com/solder_state/n/n13c49f08ca1f
No.50 LFO/VCO rebuild 2 3 1 0 0 0 NANO/AD9833 https://note.com/solder_state/n/nd2c22a73e8fe
No.49 Clock Divider 11 0 0 0 0 0 TC4040BP https://note.com/solder_state/n/n7979cda44dcb
No. 47 Sample & hold 3 2 1 0 0 0 LF398 https://note.com/solder_state/n/n29b52f4f01f1
No.46 Dual Envelope generator 4 8 0 0 0 0 NANO https://note.com/solder_state/n/n6fb73eb1d8b8
No.45 Diode clip Distortion 2 3 0 0 0 0 NONE https://note.com/solder_state/n/n5f35e2e84a3e
No.44 Wave shaper & VCA 2 1 0 0 0 0 NONE https://note.com/solder_state/n/nfdc2e198255a
No.43 Envelope Follower 4 3 0 0 0 0 NONE https://note.com/solder_state/n/n110e9ba066b3
No.42 PCM drum 6 4 2 1 0 0 NSX-1/SAMD https://note.com/solder_state/n/neabe7e014c11
No.40 Voltage controlled switch 8 1 0 1 0 0 NJU211 https://note.com/solder_state/n/n98883e71f814
No.39 Diode ladder VCF 3 3 0 0 0 0 NONE https://note.com/solder_state/n/n598f23105ec4
No.38 Touch controller 5 1 1 4* 0 0 NANO/MPR121 https://note.com/solder_state/n/ncd42925f726b
No.37 Overflow folding VCO 4 3 0 1 0 0 XIAO https://note.com/solder_state/n/nf01e7c92b010
No.36 LM13700 Dual VCA 6 2 0 0 0 0 LM13700 https://note.com/solder_state/n/n3357199504d8
No.35 CV to MIDI 6 1 0 0 0 1 NANO/SSD1306 https://note.com/solder_state/n/nb618127f37c9
No.33 Dual Quantizer 7 1 0 0 1 0 SAMD/SSD1306 https://note.com/solder_state/n/nb8b9a2f212a2
No.32 Spin FV-1 multi FX 5 5 0 0 0 0 NANO/FV-1 https://note.com/solder_state/n/n1c402a78a0fe
No.31 Ring modulator & wavefold 4 3 0 0 0 0 AD633 https://note.com/solder_state/n/n9d138d74b39d
No.30 Euclidean rhythm sequencer 7 0 0 1 1 0 NANO/SSD1306 https://note.com/solder_state/n/n433b32ea6dbc
No.29 SH-101 type sequencer 7 1 TRIM 0 1 1 0 SAMD/SSD1306 https://note.com/solder_state/n/n80f4baf81226
No.28 DSP multi effector 2 0 0 0 0 0 DSP https://note.com/solder_state/n/nd9c984a9ab7a
No.27 5ch mixer 6 6 0 0 0 0 NONE https://note.com/solder_state/n/nffc1a33053be
No.26 V2044 VCF 3 3 0 0 0 0 V2044 VCF https://note.com/solder_state/n/n0fabdc23fe1e
No.25 Oscillo scope & Spectrum analyzer 3 1 1 0 1 0 NANO/SSD1306 https://note.com/solder_state/n/n6b4cc8d1c6b9
No.24 V2164 Dual VCA 6 2 0 0 0 0 V2164 https://note.com/solder_state/n/n14a8be5f7118
No.23 CHORD VCO 4 3 0 0 0 0 NANO https://note.com/solder_state/n/n681d2e07e324
No.22 Additive VCO 4 3 0 0 0 0 NANO https://note.com/solder_state/n/n30b3a8737b1e
No.20 CV/GATE 8step sequencer 3 8 1 0 0 0 CD4022BE /NE555 https://note.com/solder_state/n/n4da93d157f26
No.19 FM VCO 4 3 0 0 0 0 NANO https://note.com/solder_state/n/n88317851a4c7
No.18 2OSC VCO 3 3 1 0 0 0 NANO https://note.com/solder_state/n/n71c67b5aaeca
No.17 Multi mode Envelope generator 2 4 1 0 0 0 NANO https://note.com/solder_state/n/n69643b792274
No.16 CV/Gate sequencer & Arpeggiator 5 0 0 1 1 0 NANO/SSD1306 https://note.com/solder_state/n/n7c2809976698
No.15 TR-808/909 sample player drum 5 0 0 1 0 0 SAMD/SSD1306 https://note.com/solder_state/n/n0209d16d0d08
No.14 KICK 3 4 0 0 0 0 NANO https://note.com/solder_state/n/ne33e32660d50
No.13 Noise & Hi-hat 4 3 0 0 0 0 NANO https://note.com/solder_state/n/nf65437f12790
No.12 Clock SYNC LFO 2 4 0 0 0 0 NANO https://note.com/solder_state/n/n4c600f2431c3
No.11 MIDI to CV 4 1 0 0 0 1 NANO https://note.com/solder_state/n/n17e028497eba
No.10 Gate Burst/Delay 4 2 1 1 0 0 NANO https://note.com/solder_state/n/n28b5c43229af
No.9 6ch trigger sequencer 7 0 0 1 1 0 NANO/SSD1306 https://note.com/solder_state/n/n17c69afd484d
No.8 SX150 VCF 3 2 1 0 0 0 NANO/MCP4726 https://note.com/solder_state/n/n5136d98930a8
No.7 Quantizer 4 2 1 0 1 0 NANO/MCP4726 https://note.com/solder_state/n/nde97a0516f03
No.6 Clock multi divide 4 2 1 0 0 0 NANO https://note.com/solder_state/n/n8907f2f6e8f5
No.5 Generative sequencer 3 2 1 0 0 0 NANO/MCP4911 https://note.com/solder_state/n/n8a489f0b857a
No.4 samplar 3 1 1 0 1 0 NANO/TF PLAYER https://note.com/solder_state/n/n6057a5256042

Videos

  • Hooking together modules