ER-MOZZI-DB-03

Features

• Daughtercard to ER-PROTO-02 card
  • Uses Front Panel and Controls card
    • Controls card populated as required
      • 0-6 Jacks, 0-6 Pots
• Arduino NANO
• High Def Sound output
• Up to 6 Pots connected to A/D inputs
• Up to 5 input jacks connected to A/D inputs

Arduino Pins

• The ER-PROTO-02 controls card has 6 pots (RV1-RV6) and 6 jacks (J1-J6)
• The Arduino NANO has 8 Analog Inputs (0-7)
• RV1-RV6 are brought into the card
• 6 Jacks
  • J1-J5 Jacks can be used for analog inputs, digital inputs or digital outputs
  • J6 Jack is a dedicated output (J6) connected to Hi Def output Arduino pins D9, D10

Jacks/Headers

J9 - Eurorack Power

• Power filter

Software / Example Projects

• HAGIWO Bezier curve random CV generator
• HAGIWO Envelope Generator Module
• HAGIWO FM VCO Module
• HAGIWO Additive VCO (harmonic addition VCO)
• HAGIWO CHORD VCO with mozzi library
• Using Mozzi Library With 5 Potentiometers
• Atari Punk Synth V2
• Arduino Multi-pot Mozzi FM Synthesis
• Arduino mozzi FM VCO Module for 650 yen - Modular synth self-made
• Nuts and Volts AUDUINO Synth build for the Arduino NANO
  • Files for Nuts and Volts AUDUINO Synth
• MozMo = ATMega328 plus FTDI

HAGIWO MOZZI builds

• HAGIWO builds
• Pots
  • Install RV1-RV4 = 100K
  • Install series resistor R1-R3 1K
  • Install Pull-up/Pull-down jumpers
• Jacks
• J3-J5 = PJ398SM
• J6 = PJ366ST

Additive VCO

• HAGIWO Additive VCO Notes

• 3 pots (Fundamental Frequency, Harmonics Gain, Harmonic)
• 3 CV input jacks (V/Oct, Gain, Harmonic)
• 1 PWM output jack
  • Output swings 1V-4V
• Additive VCO Code

Chord VCO

• HAGIWO Chord VCO

• 3 pots (Root Frequency, Inversion, Chord/Wave)
• 3 CV input jacks (V/Oct, Inversion, Chord/Wave)
• 1 PWM output jack
  • Output swings 2.5V +/- 100mV
• CHORD VCO Code

FM VCO

• HAGIWO FM VCO

• 3 pots (Carrier Frequency, Mod Freq, Mod Level)
• 3 CV input jacks (V/Oct, Mod Freq, Mod Level)
• 1 PWM output jack
  • Output swings 0-5V

• FM VCO Code

Triple Mode VCO

• FM, Additive, Chord modes
• Started from Testbld Code base
  • Replaced mode select switch with RV4 mode select pot
    • RV4 is on Analog 3
    • Add RV4 = 100K to controls card
    • Add R4 = 1K to controls card
    • Add C2 = 0.1uF to controls card
    • Add R4 = 0 ohms jumper to daughtercard
• PWM output
  • Output swings 2V-3V

HAGIWO Bezier Random CV Generator

• HAGIWO Bezier Random CV Generator
  • HAGIWO Bezier Random CV Generator

Issues

Rev 1

• Switch on jacks between RV and J not wired correctly
  • Fixed in Rev 2 schematic
  • Could cut pots and wire manually
  • More easily just don't populate jack or pots that are not needed
• J2, J6 reversed on schematics (Ctrls and ER-MOZZI-DB cards)
• Add jumper J6-T to R13 other side from J2-T)

Assembly Sheet

• ER-MOZZI-DB Rev 1 Assembly Sheet