SIMPLE-6502

From Land Boards Wiki
Revision as of 19:58, 24 August 2024 by Blwikiadmin (talk | contribs) (→‎FTDI)
Jump to navigation Jump to search

Tindie-mediums.png

SIMPLE-6502 P1090254-720pxV.jpg

Features

Memory Map

  • 0x0000-0x7FFF 32KB SRAM
  • 0x8000-0x9FFF Free Space (8KB)
  • 0xA000-0xBFFF Serial (ACIA)
  • 0xC000-0xFFFF 16KB EPROM

Chip Set

LB 65C02 PARTS.jpg

  • Picture shows 3 MHz CPU
  • Received 2 MHz CPU
  • As received:

SIMPLE-6502 P1090155-720px.jpg

References

Design

CPU

U5 CPU 6502.PNG

R6502 CPU Timing

R6502 Timing-01.PNG R6502 Timing-02.PNG

R65C02 vs W65C02 vs W65C816 CPUs

U5 Pin U5 Pin Name Sig Name Pullup R65C02 sig W65C02 sig W65C816 sig
1 VSS/VPB JP1 GNDs N VSS (IN) VPB (OUT) VPB (OUT)
3 PH1OUT/ABORT NC N PH1OUT (OUT) PH1OUT (OUT) ABORT (IN)
5 NC/MLB NC N NC MLB (OUT) MLB (OUT)
7 SYNC/VPA NC N SYNC (OUT) SYNC (OUT) VPA (OUT)
35 NC/E NC N NC NC EM/NAT (OUT)
36 NC/BE Pull up Y NC BE (IN) BE (IN)
37 PH0IN/PH2IN CPUCLK N PH0IN PH2IN PH2IN
38 SO/MX VCC VCC SO* (IN) SOB (IN) MX (OUT)
39 PH2OUT/VDA PH2_OUT N PH2OUT (OUT) PH2OUT (OUT) VDA(OUT)
  • Need to lift U5-38 to use W65C816 CPU

R65C02 vs W65C02 w65c816 Pinout 800PX.png

VDA/VPA (65C816)
  • VDA/VPA
    • 00, Internal operation (invalid address bus)
    • 01, Valid Program Address
    • 10, Valid Data Address
    • 11, Opcode-fetch

EPROM/EPROM

U4 EEPROM.PNG

SRAM

U2 SRAM.PNG

Clock (Rev 1)

U7 U8 CLOCK.PNG

Clock (Rev 2)

U7 U8 CLOCK v2.PNG

UART

U1 U3 UART.PNG

FTDI

  • Does not match Grant's pinout
  • Can only use RS-232 or FTDI - one at a time

J3 FTDI.PNG

Headers / Connectors

SIMPLE-6502 REV1 CAD.PNG

J1 - RS-232 Serial

  • DB-9 Male
  • Matches Grant's pinout
  • Pinout
  1. N/C
  2. Receive
  3. Transmit
  4. Loop to pin 6
  5. GND
  6. Loop to pin 4
  7. RTS
  8. N/C
  9. N/C

J2 - Speed Select Jumper

  • 1-2 - 0.92 MHz
  • 2-3 = 1.8432 MHz

J3 - FTDI / TTL Serial

  • Requires a FTDI cross-over cable

SIMPLE-6502 J3 FTDI.PNG

  1. GND
  2. RTS* (out)
  3. +5V
  4. Receive (in)
  5. Transmit (out)
  6. N/C

J4 - 5V Power

  • 2x4 header

J4 PWR-5V.PNG

J5 / J6 - EPROM/EEPROM Select Jumpers

SIMPLE-6502 J5 J6.PNG

  • J5 - EPROM Pin 1 jumper
    • 1-2 for 28C64, 28C256 (Pull WE to VCC)
    • 2-3 for 27256, 27SF256, 27512 (Pull A14 to GND)
  • J6 - EPROM Pin 27 jumper
    • GND (2-3)

EEPROM Pin Table

27512 27256 27SF256 28C256 27128 2764 28C64 PIN PIN 2764 28C64 27128 28C256 27SF256 27256 27512
A15 VPP VPP A14 VPP VPP N/C 1 28 VCC VCC VCC VCC VCC VCC VCC
A12 A12 A12 A12 A12 A12 A12 2 27 PGM WE* PGM WE* A14 A14 A14
A7 A7 A7 A7 A7 A7 A7 3 26 A13 N/C A13 A13 A13 A13 A13
A6 A6 A6 A6 A6 A6 A6 4 25 A8 A8 A8 A8 A8 A8 A8
A5 A5 A5 A5 A5 A5 A5 5 24 A9 A9 A9 A9 A9 A9 A9
A4 A4 A4 A4 A4 A4 A4 6 23 A11 A11 A11 A11 A11 A11 A11
A3 A3 A3 A3 A3 A3 A3 7 22 OE* OE* OE* OE* OE* OE* OE*
A2 A2 A2 A2 A2 A2 A2 8 21 A10 A10 A10 A10 A10 A10 A10
A1 A1 A1 A1 A1 A1 A1 9 20 CE* CE* CE* CE* CE* CE* CE*
A0 A0 A0 A0 A0 A0 A0 10 19 D7 D7 D7 D7 D7 D7 D7
D0 D0 D0 D0 D0 D0 D0 11 18 D6 D6 D6 D6 D6 D6 D6
D1 D1 D1 D1 D1 D1 D1 12 17 D5 D5 D5 D5 D5 D5 D5
D2 D2 D2 D2 D2 D2 D2 13 16 D4 D4 D4 D4 D4 D4 D4
GND GND GND GND GND GND GND 14 15 D3 D3 D3 D3 D3 D3 D3

JP1 - CPU Pin 1

  • Install if CPU is not a WDC 65C02 or WDC 65C816

Software

  • Link to Grant's files
  • Source code
    • osi_bas.s <== the Microsoft OSI BASIC and I/O routines SOURCE all in a single file
    • Grant's I/O routines are at the end of it
  • Files to allow the source to be assembled on a Windows based machine
    • assemble.bat <== double click to assemble osi_bas.s and link to binary file "osi_bas.bin"
    • This should be exactly 16K
    • osi_bas.cfg <== configuration file for the linker (ensure ORG and entries in this file match if you change any)
    • ca65.exe <== the assembler from the cc65 package. Use this. The new version on the cc65 site crashes!
    • ld65.exe <== linker from the cc65 package
  • Output files
    • osi_bas.bin <== the ROM fine in pure binary
    • osi_bas.lst <== Assembly listing file
    • rom.hex <== the ROM fine in standard INTEL-HEX format
  • To allow simple re-assembly, extract all files to the same folder
    • Freeware utilities are available to convert the "bin" file to HEX or s19 (etc) - use your internet search tool to find
  • All source code, assembler binaries and the HEX dump of the ROM is here
    • It is in standard INTEL-HEX format for uploading to a suitable programmer.

First Unit Checkout (Rev 1 PCB)

SIMPLE-6502 P1090185-720PX.jpg

Install Sockets

  • Machined pin sockets

SIMPLE-6502 P1090153-720px.jpg

Install Passives

SIMPLE-6502 P1090159-720px.jpg

Power

  • Install 2x4 at J4
  • Power card via J4 with 5V
  • Check power pins on parts

Clock

  • Install Clock parts
    • Did not have 270 pF cap, used 220 pF
    • U7 (74HC04)
    • Y1 1.8432 MHz crystal
    • Clock "doubling" with 74HC04 part
    • Worse with 74HC14
    • Switched to 74LS04 - works well
  • Install clock divider
    • U8 (74HC74)
  • Check clocks at J2
    • Pin 1 s/b 0.9216 MHz
    • Pin 3 s/b 1.8432 MHz
    • Outputs are OK
  • Need to change P/L and S/S to 74LS04

SIMPLE-6502 CLK.png

AN12 Fig 1d.PNG

  • Used 1nF cap instead of 1200pF
  • Starts reliably but has a glitch
    • Seems to run OK
    • Reset is weird, sometimes does not boot and takes a couple of presses
    • Not sure if this is clock related
  • Order new 74LS04 parts
  • See Rev 2 updates

Reset

  • Install U9
  • Install pushbutton switch SW1
  • Reset button gets stretched by Power Monitor U9
  • Measure at 6502 U5 pin 40
  • Falling edge scope cap

SIMPLE-6502 RESET-FALLING.png

  • Rising edge scope cap

SIMPLE-6502 RESET-RISING.png

  • Switch failed, replaced - works

EPROM

  • SST27C256 EEPROM
    • 32 KB part
    • Using first 16KB of EEPROM
    • J5 EEPROM pin 1 = VPP = VCC or GND
      • Jumper J5:2-3
    • J6 EEPROM pin 27 = A14 = GND
      • Jumper J6:2-3
  • U1 - Do not install MAX232
  • R65C02 CPU
    • Install JP1 on rear of card as wire

EEPROM Programming

SIMPLE-6502 TL866Plus Program.png

  • Device programmed/verified

Install CPU, ROM, RAM, ACIA

  • Do not install MAX232 yet

Test FTDI Serial

Card Without MAX232

  • With DB-9 connector
  • Install DB-9 Male
  • Holes don't line up well, but 4-40 screws can fit
  • Without MAX232

SIMPLE-6502 P1090254-720pxV.jpg

Built Card

FTDI DCE P1090192-720PXV.jpg

SIMPLE-6502 P1090192-720px.jpg

  • DB-9 connectors connected together

SIMPLE-6502 P1090191-720px.jpg

  • Works

SIMPLE-6502 Booting.png

Performance

  • TeraTerm settings

SIMPLE-6809 TeraTerm Setup.PNG

  • Test software
10 FOR I =1 TO 10000
20 PRINT I
30 NEXT I
  • Time ~38 secs

Mechanicals

  • Rev 1 board
    • Rev 2 board has the same mechanical dimensions, but some parts are different

SIMPLE-6502 REV1 MECHS.PNG

PCB Issues

Rev 2

  • See clock section above for issues found during Rev 1 board checkout

SIMPLE-6502 Rev2 ClockUpdates.PNG

  • R8, R9 missing 2.7K marking on silkscreen
    • Updated on Rev 2 interactive BOM
  • C6, C14 change value to 33 pF
    • Symptom with 22 pF caps was wrong oscillation frequency (approx 2.1 MHz)
    • Crystal is 18pF
  • U7 has to be 74HC04 with these other value parts
  • Measured oscillator circuit timing/voltages

SIMPLE-6502 Rev2 Oscillator.png

Rev 1

  • Clocking not optimal - see notes above in clock section for debug issues

Assembly Sheet

Assembly Sheet Rev 2

  • SIMPLE-6502 Rev 2 Interactive BOM
  • Install jumper JP1 on rear of board if CPU is not a WDC 65C02 or WDC 65C816
  • Install jumpers J5-2 to -3 and J6-2 to -3
  • Clock changes from Grant's design
  • U7 is 74HC04 (silkscreen shows 74LS04)
    • 74LS04 might work if the Resistor values in the clock circuit are changed
  • Jumper J2 clock to run the CPU at either 1.8432 MHz or half speed 0.9216 MHz

Assembly Sheet Rev 1

Retrieved from "http://land-boards.com/blwiki/index.php?title=SIMPLE-6502&oldid=26430"