Features
- Arduino Pro Mini
- Detachable Human Interface design (HID)
- Flexible Input power
- On-board DC/DC buck regulator allows 7-23V input
- Direct 7-9V input (USE VRAW jumper)
- 3.3V of 5V Arduino support
- Measured 12 mA with 9V input and 3.3V Arduino Pro Mini
- I/O Boards
- Mounts in a standard extruded Aluminum enclosure
Arduino Pro Mini
- Inexpensive and widely available
- Arduino Pro Mini sCHEMATIC
- I/O - 14 digital input/output pins (of which 6 can be used as PWM outputs)
- Serial: 0 (RX) and 1 (TX).
- Used to receive (RX) and transmit (TX) TTL serial data.
- These pins are connected to the TX-0 and RX-1 pins of the six pin header.
- External Interrupts: 2 and 3.
- These pins can be configured to trigger an interrupt on a low value, a rising or falling edge, or a change in value.
- See the attachInterrupt function for details.
- PWM: 3, 5, 6, 9, 10, and 11.
- Provide 8-bit PWM output with the analogWrite function.
- SPI: 10 (SS), 11 (MOSI), 12 (MISO), 13 (SCK).
- These pins support SPI communication, which, although provided by the underlying hardware.
- LED: 13.
- There is a built-in LED connected to digital pin 13.
- When the pin is HIGH value, the LED is on, when the pin is LOW, it's off.
- 6 analog inputs
- On-board resonator (8 or 16 MHz)
- Reset button
- A six pin header can be connected to an FTDI cable provide USB power and communication to the board
- 3.3 or 5V
- 8 MHz (3.3V) or 16 MHz (5V)
- Programmable in Arduino IDE
Detachable Human Interface design (HID)
- OLED
- Rotary Encoder with switch
- Can leave attached to main board until installing in box
Input Power Options
- 2.1mm DC Power Connector Jack
- Mini360 Switching Mode Power Supply
- Wide input voltage range
- 5-23V (for 3.3V Arduino Pro Mini)
- 7-23V (for 5V Arduino Pro Mini)
- About $1
- Jumper to use raw input and not populate the Mini360
- Uses the inputs jack as RAW power into the Arduino Pro Mini
- 3.35-12 V (3.3V model) or 5-12 V (5V model)
= RF Filters
- RF filter into Switching regulator board
- 2nd RF filter into HID card
Connectors
J1 - OLED
- SDA
- SCL
- +VCC
- GND
J2, J4 - On Base and HID card(s)
- Can detach HID to mount in box
- Pinout
- GND
- ENCODER A
- ENCODER B
- ENCODER SWITCH
- I2C_SCL
- I2C_SDA
- VCC
- GND
- Connect here to use the BNC or SMA jacks on the rear (option)
J5 - Arduino Pins
J6 - Voltage Adjustment
- Adjust voltage for 3.3V or 5V to match Pro Mini voltage before installing jumper
J9 - Use Raw Power
FTDI (on Arduino Pro Mini)
- Used to download program to Arduino Pro Mini
Human Interface (HID)
- OLED
- Rotary Switch with Pushbutton
- Detachable board
- Can be mounted to Front Panel of enclosure
OLED
- 0.91" 128x32 or so rotary switch (installed in SW1 location) is to the right
- 0.96" 128x64 (rotated) with rotary switch (installed in SW1 location) below
- SSD1306 family of displays
- Connections to Arduino Pins
Rotary Encoder
- Connections to Arduino Pins
I/O Boards
- Base board has 3 optional BNC (P1-P3) or edge launch SMA (P4-P6) connectors
- Brought to headers (J4, J7, J8)
- Easy to application specific custom I/O cards
- All Arduino pins brought to J5 - 2x13 pin header
- I/O pins are on 0.1" grid for easier prototyping
- P2-P13, A0-A3
- A4/A5 or SDA/SCL (connects to OLED)
- Location of mounting holes
DB-25 Example
- Standard DB-25 female
- Does not have 26 pin of the 2x13 header in the box
- OK, extra powers/grounds at the ends
- Connect with 1:1 cables to 2x10/2x3 Dupont receptacles
Mechanicals/Enclosure
- Board is designed to fit into Aluminum Project Box Enclosure DIY 100*76*35mm - ebay search
Test
Scanning...
I2C device found at address 0x3C !
done
- May require a different constructor
U8X8_SSD1306_128X32_UNIVISION_HW_I2C u8x8(U8X8_PIN_NONE);
Software
GitHub Repository
Total Memory usage with u8x8 Library and Rotary Encoder Code
Sketch uses 7062 bytes (22%) of program storage space.
Maximum is 30720 bytes.
Global variables use 475 bytes (23%) of dynamic memory,
leaving 1573 bytes for local variables. Maximum is 2048 bytes.
Minimal u8x8 code
Sketch uses 6198 bytes (20%) of program storage space. Maximum is 30720 bytes. Global variables use 446 bytes (21%) of dynamic memory, leaving 1602 bytes for local variables. Maximum is 2048 bytes.
Download/Programming
- FTDI cable
- FTDI jumper is set to 3.3V
- Power wire is not used
- Other connections are 1:1
IDE setup
- Board: Arduino Pro or Pro Mini
- Processor: ATMega328P (3.3V, 8 MHz)
Assembly Instructions