Difference between revisions of "ER-VCF-02"

From Land Boards Wiki
Jump to navigation Jump to search
 
(6 intermediate revisions by the same user not shown)
Line 1: Line 1:
[[FILE:ER-VCF-02_Front-Back-720px.jpg]]
+
[[FILE:ER-VCF-02_f-b_720px.jpg]]
  
 
== Features ==
 
== Features ==
Line 61: Line 61:
 
* 3.5mm mono connector
 
* 3.5mm mono connector
 
* Tip - signal
 
* Tip - signal
 
=== Front Panel Controls to Analog Card Connectors ===
 
 
==== J5 - Pot connector ====
 
 
[[file:ER-PROTO-CTLS-6-01_J5.PNG]]
 
 
==== J10 - Jack connector ====
 
 
[[file:ER-PROTO-CTLS-6-01_J10.PNG]]
 
  
 
=== Analog Card Connectors ===
 
=== Analog Card Connectors ===
Line 76: Line 66:
 
==== J1 - Eurorack Power ====
 
==== J1 - Eurorack Power ====
  
[[file:ER-VCF-01-DB_J1.PNG]]
+
[[file:ER-VCF-02-DB_J1.PNG]]
  
 
==== J2 - POT (from Controls card) ====
 
==== J2 - POT (from Controls card) ====
Line 94: Line 84:
 
=== Rev 1 ===
 
=== Rev 1 ===
  
* Working
+
* No issues, working
  
 
== Videos ==
 
== Videos ==

Latest revision as of 21:10, 31 May 2023

ER-VCF-02 f-b 720px.jpg

Features

  • This is a diode ladder VCF - original design by Moritz Klein, with a couple of small adaptions made by T Killa
  • There are two CV inputs
    • CV1 with an attenuator to control the amount
    • CV2 with an attenuverter so it's possible to invert the signal as well as controlling the amount of modulation
  • The filter is a low-pass filter only
  • 3U tall
  • 6 HP (30mm) wide
  • Uses ER-PROTO-02 controls cards

Credits

Pots/Connectors

Front Panel Pots

  • POT RV1 - CV1 Attenuator adjustment
  • POT RV2 - CV2 Attenuaverter adjustment
  • POT RV3 - Not used
  • POT RV4 - Not used
  • POT RV5 - Resonance adjustment
  • POT RV6 - Cutoff Frequency adjustment

POT RV1 - CV1 Attenuator adjustment

POT RV2 - CV2 Attenuaverter adjustment

POT RV5 - Resonance adjustment

POT RV6 - Cutoff Frequency adjustment

Front Panel External Connectors

  • J3 - Audio In
  • J4 - CV Amount
  • J5 - Attenuaverter input
  • J6 - Audio Out

J3 - Audio In

  • 3.5mm mono connector
  • Tip - signal

J4 - CV Amount

  • 3.5mm mono connector
  • Tip - signal

J5 - Attenuaverter input

  • 3.5mm mono connector
  • Tip - signal

J6 - Audio Out

  • 3.5mm mono connector
  • Tip - signal

Analog Card Connectors

J1 - Eurorack Power

ER-VCF-02-DB J1.PNG

J2 - POT (from Controls card)

ER-VCF-02-DB J2.PNG

J3 - Jacks (to/from Controls card)

ER-VCF-02-DB J3.PNG

Schematics

ER-VCF-02 REV 1 Schematic

Issues

Rev 1

  • No issues, working

Videos

  • Design base on Low Pass only version of Moritz Klein's design

Assembly Sheet

  • Three card set
    • Front Panel
    • ER-PROTO-02 Controls card
      • RV1, RV2, RV5, RV6 (No RV3, RV4)
      • J3-J5
    • Analog card