MMBASIC on XIAO RP2040

From Land Boards Wiki
Jump to navigation Jump to search

QTPy49 MMBASIC P18412-720px.jpg

Overview

  • Card set running BASIC Interpreter for the Raspberry Pi Pico on Seeed Studio XIAO RP2040
  • MMBasic is a Microsoft BASIC compatible implementation of the BASIC language with floating point, integer and string variables, arrays, long variable names, a built in program editor and many other features
  • 8 Flash locations for storage.
  • Support for SD Card

MMBASIC Credits

Peter Mather led the project, ported the MMBasic interpreter to the Raspberry Pi Pico and wrote the hardware device drivers. Geoff Graham wrote the MMBasic interpreter and the manual. Mick Ames wrote the PIO compiler and its corresponding documentation.

Hardware

Seeed Studio XIAO RP2040

QTPy49 breakout card

SD Card

SD Card Wiring

Signal SD_CARD_X49 QTPy49 conn QTPy GP PiPico Pin
SPI_SCLK J1-3 J3-6 GP2 GPIO2
SPI_MOSI J1-4 J3-4 GP3 GPIO3
SPI_MISO J1-2 J3-5 GP4 GPIO4
SPI_SS J1-5 J9-3 GP26 GPIO26
GND J1-1 J9-1 GND GND
VCC (3.3V) J1-7 J9-2 VCC VCC

SD Configuration

OPTION SYSTEM SPI GP2, GP3, GP4
OPTION SDCARD GP26
OPTION COLOURCODE ON

  • Verify it is working
> FILES
A:/
   <DIR>  basic
   <DIR>  bmps
   <DIR>  demos
   <DIR>  games
   <DIR>  jpegs
   <DIR>  lbcards
   <DIR>  performance
   <DIR>  wave
8 directories, 0 files

RS-232 (option)

DTE P562-720px.jpg

  • TTL to RS-232 converter
  • Male DB-9 connector
  • FTDI pinout (reversed directions to directly connect to FTDI Interface)
  • 49x49mm card
  • 4x 4-40 holes
  • DTE card
  • Command to use serial
OPTION SERIAL CONSOLE GP0, GP1

RS-232 Wiring

DTE signal DTE pin QTPy GP PiPico Pin
GND H1-1 GND J4-1
CTS H1-2 N/C N/C
VCC H1-3 VCC J4-2
TX H1-4 TX_D6 J4-3
RX H1-5 RX_D7 J4-4
RTS H1-6 N/C N/C

MMBASIC Card Stack-up

QTPY49 MMBASIC P18420-720pxV.jpg

Software

Install MMBASIC on Seeed XIAO RP2040

  • Hold down the "BOOT" button
    • The "B" is written on the board shown to the right
  • Connect the XIAO RP2040 via USB C cable to your computer while still pressing the button
  • The computer then will appear a disk driver(RP1-RP2)
  • Download the PicoMite_Firmware.zip
  • Drag the .uf2 file to the disk drive ("RP1-RP2")
  • Card will re-boot
  • Connect in TeraTerm over serial
  • Free memory
> print mm.ver
 5.070501

> memory

Program:
   0K ( 0%) Program (0 lines)
 124K (100%) Free

RAM:
   1K ( 1%) 3 Variables
   0K ( 0%) General
 155K (99%) Free

GPIO from MMBASIC

QTPy49 Marking GPIO
A0 GP26 (SD_SS)
A1 GP27
A2 GP28
A3 GP29
I2C_SDA GP6
I2C_SCL GP7
RX GP1
TX GP0

MMBASIC - Using Pins

  • Digital I/O
SETPIN GP27, DIN:' Digital Input
SETPIN GP28, DOUT:' Digital Output
PIN(GP28) = 1:'Digital output

  • Analog Input
SETPIN GP29, AIN:' Analog Input

  • SETPIN(s) for Serial and I2C
SETPIN GP1, GP0, COM1
SETPIN GP6, GP7 I2C2

On-Board LED

  • No Built-in support in MMBASIC for the on-board NEOPIXEL
  • Red, Green, Blue LED
  • Pull Low to turn on RGB LED bits
  • At-boot - RGB LED blinks Cyan/Green by MMBASIC
  • Red LED = GP17
  • Green LED = GP16
  • Blue LED = GP25 (Used by MMBASIC)
' Make pins outputs
SETPIN GP17, DOUT:' Red LED
SETPIN GP16, DOUT:' Green LED
SETPIN GP25, DOUT:' Blue LED
' Turn off LEDS
PIN(GP17)=1:' Turn off Red LED
PIN(GP25)=1:' Turn off Blue LED
PIN(GP16)=1:' Turn off Green LED
' Turn on LEDs
PIN(GP17)=0:' Turn on Red LED
PIN(GP25)=0:' Turn on Blue LED
PIN(GP16)=0:' Turn on Green LED

Demo Code