Difference between revisions of "PDP-11 ON RETRO-EP4CE15"

From Land Boards Wiki
Jump to navigation Jump to search
Line 141: Line 141:
  
 
[[File:RETROEP4CE15-Serial.PNG]]
 
[[File:RETROEP4CE15-Serial.PNG]]
 +
 +
==== Serial Ports - I/O connector ====
  
 
* fpgaRx1 (in) = PIN_C11
 
* fpgaRx1 (in) = PIN_C11
Line 148: Line 150:
 
* fpgaRts1 = U7-44 = PIN_F10
 
* fpgaRts1 = U7-44 = PIN_F10
 
* fpgaCts1 = U7-46 = PIN_B11
 
* fpgaCts1 = U7-46 = PIN_B11
 
==== I/O connector ====
 
 
 
* Second serial port on I/O connector
 
* Second serial port on I/O connector
 
* rx2 (in) = PIN_M18
 
* rx2 (in) = PIN_M18

Revision as of 18:20, 2 March 2021

Work in Progress

RETROEP4CE15 REV4 P376-annotated-720px.jpg

Build

FPGA

Software

Configuration Switches/Jumpers/LEDs

J3 - Configuration Jumpers (5CEFA2F23 FPGA Card pin numbers)

J3-footprint.PNG

J3 MAP FPGA PINS.PNG

Function DIP Switch FPGA Pin
rp boot
(out=boot to debugger)
(in=rp boot)
1 PIN_L17
Buzzer
(out=not buzz)
(in=buzzes constantly)
2 PIN_K17
rk boot
(out=rk boot)
(in=boot to debugger)
3 PIN_K22
Swap console
(out=vga console)
(in=RS-232 console)
4 PIN_K21

Switches

LEDS-SWITCHES P1404-720px.jpg

Function J10 Pin FPGA Pin
resetbtn SW9 PIN_J16
sw_halt J10-30 PIN_N14
sw_cont J10-32 PIN_P15
led_run D8 PIN_T15

Connectors

P1 - VGA (5CEFA2F23 Card)

  • videoR0 = U8-49 = PIN_E12
  • videoR1 = U8-50 = PIN_D12
  • videoG0 = U8-51 = PIN_D13
  • videoG1 = U8-52 = PIN_C13
  • videoB0 = U8-53 = PIN_B13
  • videoB1 = U8-54 = PIN_A13
  • hSync = U8-55 = PIN_A15
  • vSync = U8-56 = PIN_A14

P2 - PS/2 Keyboard

PS2 Mapping.PNG

  • PS2DAT = U7-8 = PIN_BANK_2A_AA1
  • PS2CLK = U7-8 = PIN_NANK_2A_AA2

J1 - I/O Connector (5CEFA2F23 FPGA Card pin numbers)

J1 MAP FPGA PINS.PNG

  • J1-50 = GND
  • J1-49 = GND
  • J1-48 = PIN_M22 = resetbtn
  • J1-47 = PIN_L22 = sw_cont
  • J1-46 = PIN_L18 = sw_halt
  • J1-45 = PIN_L19 = tx2
  • J1-44 = PIN_M18 = rx2
  • J1-43 = PIN_N19 = rts2
  • J1-42 = PIN_M21 = cts2
  • J1-41 = PIN_M20 = led_run
  • J1-40 = PIN_N20 = xu_sclk
  • J1-39 = PIN_N21 = xu_mosi
  • J1-38 = PIN_P16 = xu_miso
  • J1-37 = PIN_P17 = xu_debug_tx
  • J1-36 = PIN_T20 = xu_cs
  • J1-35 = PIN_T19 = max7219_load
  • J1-34 = PIN_P22 = max7219_data
  • J1-33 = PIN_R21 = max7219_clock
  • J1-1 = VCC
  • J1-2 = VCC

J4 - USB-B B (5CEFA2F23 FPGA Card pin numbers) Serial Port

  • On-board FT230X FTDI USB to Serial

RETROEP4CE15-Serial.PNG

Serial Ports - I/O connector

  • fpgaRx1 (in) = PIN_C11
    • Needs weak pullup
      • set_instance_assignment -name WEAK_PULL_UP_RESISTOR ON -to rxd1
  • fpgaTx1 (out) = PIN_G10
  • fpgaRts1 = U7-44 = PIN_F10
  • fpgaCts1 = U7-46 = PIN_B11
  • Second serial port on I/O connector
  • rx2 (in) = PIN_M18
  • tx2 (out) = PIN_L19
  • rts2 (out) = PIN_N19
  • cts2 (in) = PIN_M21

P4 - SD Card (5CEFA2F23 FPGA pin numbers)

SD Card Mapping.PNG

  • SDCS = U7-57 = PIN_BANK_7A_B15
  • MOSI = U7-58 = PIN_BANK_7A_C15
  • SCK = U7-59 = PIN_BANK_7A_C16
  • MISO = U7-60 = PIN_BANK_7A_B16
  • SD_DETECT - PIN_B12

External 8 Digit 7 segment MAX7219 LED

  • PIN_L15 max7219_data J10-24
  • PIN_N12 max7219_load J10-26
  • PIN_N15 max7219_clock J10-28

Resources

Pin List

# Analysis & Synthesis Assignments
# ================================
set_global_assignment -name FAMILY "Cyclone V"
set_global_assignment -name TOP_LEVEL_ENTITY top
set_global_assignment -name EDA_DESIGN_ENTRY_SYNTHESIS_TOOL "Design Compiler"

# Fitter Assignments
# ==================
set_global_assignment -name DEVICE 5CEFA2F23I7
set_global_assignment -name STRATIX_DEVICE_IO_STANDARD "3.3-V LVTTL"
set_global_assignment -name CRC_ERROR_OPEN_DRAIN OFF
set_global_assignment -name CYCLONEII_RESERVE_NCEO_AFTER_CONFIGURATION "USE AS REGULAR IO"
set_global_assignment -name FORCE_CONFIGURATION_VCCIO ON

# Pin & Location Assignments
# ==========================

# Clock and external reset button
set_location_assignment PIN_M9 -to clkin
set_location_assignment PIN_M22 -to resetbtn
set_instance_assignment -name WEAK_PULL_UP_RESISTOR ON -to resetbtn
# Control switches
set_location_assignment PIN_L22 -to sw_cont
set_instance_assignment -name WEAK_PULL_UP_RESISTOR ON -to sw_cont
set_location_assignment PIN_L18 -to sw_halt
set_instance_assignment -name WEAK_PULL_UP_RESISTOR ON -to sw_halt
set_location_assignment PIN_M20 -to led_run
# Jumpers on front edge
set_location_assignment PIN_L17 -to switch[0]
set_location_assignment PIN_K17 -to switch[1]
set_location_assignment PIN_K22 -to switch[2]
set_location_assignment PIN_K21 -to switch[3]
# SDRAM
set_location_assignment PIN_Y9 -to dram_addr[12]
set_location_assignment PIN_T9 -to dram_addr[11]
set_location_assignment PIN_R6 -to dram_addr[10]
set_location_assignment PIN_W8 -to dram_addr[9]
set_location_assignment PIN_T8 -to dram_addr[8]
set_location_assignment PIN_U8 -to dram_addr[7]
set_location_assignment PIN_V6 -to dram_addr[6]
set_location_assignment PIN_U7 -to dram_addr[5]
set_location_assignment PIN_U6 -to dram_addr[4]
set_location_assignment PIN_N6 -to dram_addr[3]
set_location_assignment PIN_N8 -to dram_addr[2]
set_location_assignment PIN_P7 -to dram_addr[1]
set_location_assignment PIN_P8 -to dram_addr[0]
set_location_assignment PIN_P9 -to dram_ba_1
set_location_assignment PIN_T7 -to dram_ba_0
set_location_assignment PIN_AA7 -to dram_cas_n
set_location_assignment PIN_V9 -to dram_cke
set_location_assignment PIN_AB11 -to dram_clk
set_location_assignment PIN_AB5 -to dram_cs_n
set_location_assignment PIN_P12 -to dram_dq[15]
set_location_assignment PIN_R12 -to dram_dq[14]
set_location_assignment PIN_U12 -to dram_dq[13]
set_location_assignment PIN_R11 -to dram_dq[12]
set_location_assignment PIN_R10 -to dram_dq[11]
set_location_assignment PIN_U11 -to dram_dq[10]
set_location_assignment PIN_T10 -to dram_dq[9]
set_location_assignment PIN_U10 -to dram_dq[8]
set_location_assignment PIN_AA8 -to dram_dq[7]
set_location_assignment PIN_AB8 -to dram_dq[6]
set_location_assignment PIN_AA9 -to dram_dq[5]
set_location_assignment PIN_Y10 -to dram_dq[4]
set_location_assignment PIN_AB10 -to dram_dq[3]
set_location_assignment PIN_AA10 -to dram_dq[2]
set_location_assignment PIN_Y11 -to dram_dq[1]
set_location_assignment PIN_AA12 -to dram_dq[0]
set_location_assignment PIN_V10 -to dram_udqm
set_location_assignment PIN_AB7 -to dram_ldqm
set_location_assignment PIN_AB6 -to dram_ras_n
set_location_assignment PIN_W9 -to dram_we_n
# Serial port (USB-to-Serial)
set_location_assignment PIN_C11 -to rx1
set_location_assignment PIN_G10 -to tx1
set_location_assignment PIN_F10 -to rts1
set_location_assignment PIN_B11 -to cts1
# Second serial port
set_location_assignment PIN_L19 -to tx2
set_location_assignment PIN_M18 -to rx2
set_location_assignment PIN_M21 -to cts2
set_location_assignment PIN_N19 -to rts2
# SD Card
set_location_assignment PIN_C16 -to sdcard_sclk
set_location_assignment PIN_B15 -to sdcard_cs
set_location_assignment PIN_B16 -to sdcard_miso
set_location_assignment PIN_C15 -to sdcard_mosi
# Seven segment display (on J1)
set_location_assignment PIN_R21 -to max7219_clock
set_location_assignment PIN_P22 -to max7219_data
set_location_assignment PIN_T19 -to max7219_load
# Ethernet
set_location_assignment PIN_T20 -to xu_cs
set_location_assignment PIN_P17 -to xu_debug_tx
set_location_assignment PIN_P16 -to xu_miso
set_location_assignment PIN_N21 -to xu_mosi
set_location_assignment PIN_N20 -to xu_sclk
# PS/2 Keyboard
set_location_assignment PIN_AA2 -to ps2k_c
set_location_assignment PIN_AA1 -to ps2k_d
# Video
set_location_assignment PIN_A15 -to vgah
set_location_assignment PIN_A14 -to vgav
set_location_assignment PIN_A13 -to o_vgab[1]
set_location_assignment PIN_B13 -to o_vgab[0]
set_location_assignment PIN_C13 -to o_vgag[1]
set_location_assignment PIN_D13 -to o_vgag[0]
set_location_assignment PIN_D12 -to o_vgar[1]
set_location_assignment PIN_E12 -to o_vgar[0]