PiPicoMite01

From Land Boards Wiki
Jump to navigation Jump to search

PiPicoMite01 FRONT 3D.png

Features

  • Raspberry Pi Pico
    • All pins brought to header
    • Pin marking on rear
  • VGA (1:2:1 - R:G:B)
  • PS/2 Keyboard
    • 5V to keyboard with voltage translator
  • SD Card
    • Full size card
    • Up to 32GB
  • Stereo audio
    • 3.5mm jack
  • 16-bit GPIO
    • MCP23017 port expander
    • I2C1
    • 2x20 0.1" pitch header
    • Jumper selectable terminators
  • Power options
    • 5V power input via USB B or 0.1" pitch header
    • 3.3V output header
  • 120mmx70mm outline
  • (4) 6-32 Mounting holes

Pin Marking on Rear

PiPicoMite01 REAR 3D.png

Schematic

Connectors

GP FUNCTION PICO PIN
GP6 AUDIO-L 9
GP7 AUDIO-R 10
GND AUDIO-GND 8
3.3V PS2_3.3V
VSYS PS2_5V 39
GP8 PS2_CLK 11
GP9 PS2_DATA 12
GND PS2_GND 13
3.3V SD_3.3V
GP12 SD_MISO 16
GP11 SD_MOSI 15
GP10 SD_SCK 14
GP13 SD_SLVSEL 17
GND SD_GND 18
GP18 VGA_BLU 24
GND VGA_GND 23
GP20 VGA_GRN_HI 26
GP19 VGA_GRN_LO 25
GP16 VGA_HSYNC 21
GP21 VGA_RED 27
GP17 VGA_VSYNC 22

H1 - 3.3V Power Out

PiPicoMite01 H1 3p3V.PNG

J1 - SD Card

PiPicoMite01 J1 SD Card.PNG

J2 - USB B Power Connectors

  • Full size USB B connector
  • No USB signal connections, just used for power

J3/J5 Pico Connectors

PiPicoMite01 J4-5 PiPico.PNG

J4 - I2C Terminators

  • Install shunts to terminate SDA, SCL signals

J6 - GPIO

File:PiPicoMite01 J6 GPIO.PNG

J7 - Audio

PiPicoMite01 J7 Audio.PNG

J8 - PS/2 Keyboard

PiPicoMite01 J8 Keyboard.PNG

J9 - 5V Distribution

PiPicoMite01 J9 5V.PNG

J10 - I2C INT

  • Install jumper to connect Interrupt from MCP23017 to GP0 pin on Pico
  • No Pull-up

P1 - VGA

PiPicoMite01 P1 VGA.PNG

Prototype

Cabling

FUNCTION GP PICO PIN CARD SIG PIN COLOUR
AUDIO-L GP6 9 GRID49 AUD-L C1 VIO
AUDIO-R GP7 10 GRID49 AUD-GND D1 BLK
AUDIO-GND GND 8 GRID49 AUD-R E1 YEL
PS2_3.3V 3.3V 3.3V 4 RED
PS2_5V VSYS 39 PWR1 2 ORG
PS2_CLK GP8 11 CLK1 6 VIO
PS2_DATA GP9 12 DAT1 8 YEL
PS2_GND GND 13 GND 10 BLK
SD_3.3V 3.3V 3.3V 7 RED
SD_MISO GP12 16 MISO 2 YEL
SD_MOSI GP11 15 MOSI 4 BLU
SD_SCK GP10 14 SCLK VIO
SD_SLVSEL GP13 17 -SDCS GRY
SD_GND GND 18 GND BLK
VGA_BLU GP18 24 VGA B4 (R12=270) 12 BLU
VGA_GND GND 23 VGA GND 19 GRN
VGA_GRN_HI GP20 26 VGA G5 (R6=390) 6 GRN
VGA_GRN_LO GP19 25 VGA G4 (R7=820) 7 GRN
VGA_HSYNC GP16 21 VGA HS 17 GRY
VGA_RED GP21 27 VGA R4 (R1=270) 1 ORG
VGA_VSYNC GP17 22 VGA VS 18 WHT

Raspberry Pi Pico in a Small Plastic Project Box

Pico Plastic Box P18136 720px.jpg

VGAX49

VGAX49 P901-cropped-720px.jpg

  • VGAX49
  • Resistors Values
    • Selected for 0.7V output on analog RGB pins
    • R12 = 270
    • R6 = 390
    • R7 = 820
    • R1 = 270
R,B G RES G
Rs 75 R1 390 75
Rm 270 R2 820 264.298
Vin 3.3 RM 264.298 3.3
Vout 0.717 0.729
I (mA) 9.57 I (mA) 9.73

PS2X49

PS2X49 P897 cropped 512pxV.jpg

  • PS2X49
  • PWR1 is the power to the PS/2 #1, #2 connectors
  • +3.3V connections are needed when the TXS0104 translator is installed
  • Routing
    • CLK1, DAT1 on J3 go to J1 (Purple)
    • CLK2, DAT2 on J3 go to J2 (Not used)

J3-schem.PNG

SD CARD X49

SDCARDX49 P935 cropped-512px.jpg

GRID49

GRID49 WIRING.PNG

PiceMite VGA Audio.PNG

  • C1 = Audio_In-L
  • D1 - GND
  • E1 - Audio_In-R

Mechanicals

PicoMite01 Rev1 Mechs.PNG

Assembly Sheet

PicoMite01 Rev1 Assembly Sheet